Description: Ejector Movement Failure RAP 311-320-00-120 The ejector is not at the home position. 311-322-00-120 The ejector fails to perform a cycle of operation. NOTE: A cycle of operation for the ejector is to move from the home position to the out position and back to the home position.
Remedy: NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors. NOTE: For clarity, the 1K LCSS is shown removed from the machine. Enter dC330 code 011-322, ejector out sensor, Q11-322. Actuate Q11-322. The display changes. Y↓N→Go to Flag 2. Check Q11-322. Refer to: • 311F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J8, 1K LCSS PWB • 311C-120 1K LCSS Power Distribution RAP. Install new components as necessary: • Ejector out sensor, PL 11.114 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330 code 011-320, ejector home sensor, Q11-320. Actuate Q11-320. The display changes. Y↓N→Go to Flag 1. Check Q11-320. Refer to: • 311F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J8, 1K LCSS PWB • 311C-120 1K LCSS Power Distribution RAP. Install new components as necessary: • Ejector home sensor, PL 11.114 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330 code 011-023 to check the operation of the ejector motor, MOT11-020. MOT11- 020 runs. Y↓N→Go to Flag 3. Check MOT11-020. Refer to: • 311F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. •. • P/J15, 1K LCSS PWB • 311C-120 1K LCSS Power Distribution RAP. Install new components as necessary: • Ejector assembly, PL 11.114 Item 1. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330 code 011-023 ejector cycle, check the ejector cycles. Stack the code 011-320 ejector sensor home, then cycle the ejector. Stack the code 011-322 ejector sensor out, then cycle the ejector. The ejector actuates the ejector home sensor and the ejector out sensor. Y↓N→Refer to GP 7, check the following components; •. Pulley/drive gear, PL 11.114 Item 7. • Ejector belt, PL 11.114 Item 5. Install new components as necessary: • Pulley/drive gear, PL 11.114 Item 7. • Ejector belt, PL 11.114 Item 5. The ejector cycles noisily, colliding with the end stops. Y↓N→Check the stapler to ensure the staples are correctly formed, refer to the 311-364-00-120 Stapling Failure RAP. Mis-formed staples can cause the set to hang in the stapler causing ejector movement failures. The staples are correctly formed. Y↓N→Clear the staple head of any mis-formed staples, then check the operation of the stapler. If necessary, install a new staple head unit, PL 11.116 Item 5. If the ejector is still not moving, install a new ejector assembly, PL 11.114 Item 1. Perform SCP 5 Final Actions. Enter dC330 code 011-177, ejector motor encoder sensor, Q11-177. Actuate the sensor by slowly rotating the ejector motor. The display changes. Y↓N→Go to Flag 4. Check Q11-177. Refer to: • 311F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J8, 1K LCSS PWB • 311C-120 1K LCSS Power Distribution RAP. Install new components as necessary: • Ejector motor encoder sensor, PL 11.114 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Perform the 311F-120 1K LCSS PWB Damage RAP, if necessary install a new 1K LCSS PWB, PL 11.124 Item 1.