Code: 311A-171
Description: HVF Power Distribution RAP The HVF has an integral power supply providing +24V and +5V supplies to the HVF PWB and HVF BM PWB. The AC power for the HVF power supply comes from the LVPS and base module of the machine.
Remedy: Refer to HVF Control PWB and BM PWB LEDs to identify the status of the PWBs. Close or cheat all the HVF BM interlocks. The HVF BM performs a mechanical reset. Y↓N→Go to Flag 2. +5V is available at P/J113 between pins 1 and 2. Y↓N→+5V is available at T001 on the HVF power supply module between pins 4 and 8. Y↓N→Go to Flag 1. ACL is available at PJ22 on the LVPS and base module between pins 1 and 2. Y↓N→Go to the 301C AC Power RAP and check the AC output voltages. Switch off the machine, GP 14. Disconnect all PJs on the HVF Control PWB except P/J111 and P/J113. Switch on the machine, GP 14. Go to Flag 2. +5V is available at T001 on the HVF power supply module between pins 4 and 8. Y↓N→Install a new HVF power supply module, PL 11.157 Item 1. NOTE: Before each PJ is reconnected, switch off the machine, GP 14. The HVF has a short circuit. Reconnect each PJ one at a time until short circuit is found. When the short circuit is found, repair the harness or install new components as necessary. Disconnect P/J113. Go to Flag 2. +5V is available at the harness end of P/J113 between pins 1 and 2. Y↓N→Check the connectors and harness between T001 and P/J113. Repair the harness as necessary. Install a new HVF control PWB, PL 11.157 Item 2. Go to Flag 2. +24V is available at P/J111 between pins 1 and 4. Y↓N→+24V is available at T001 between pins 1 and 5. Y↓N→Install a new HVF power supply module, PL 11.157 Item 1 Check the in-line fuse (10A), and as necessary install a new fuse PL 11.157 Item 5. Check the connectors and harness between T001 and PJ111. Repair the harness as necessary. Go to Flag 3. +24V is available at P/J111 between pins 1 and 4, between pins 2 and 5 and between pins 3 and 6. Y↓N→Go to the 311-300-00-171, 311-302-00-171, 311-303-00-171 Docking and Interlocks RAP. Go to Flag 4. +5V is available at P/J559 between pins 4 and 5. Y↓N→+5V is available at P/J132 between pins 1 and 2. Y↓N→Install a new HVF control PWB, PL 11.157 Item 2. Check the connectors and harness between P/J132 and P/J559. Repair the harness as necessary. Go to Flag 4. +24V is available at P/J559 between pins 1 and 2. Y↓N→+24V is available at P/J131 between pins 1 and 2. Y↓N→Install a new HVF control PWB, PL 11.157 Item 2. Check the connectors and harness between P/J559 and P/J131. Repair the harness as necessary. If a inserter is installed, go to P/J703. +24V is available between P/J703 pin 1 and P/ J111 pin 1. Y↓N→Go to 311-306-00-171, 311-309-00-171 HVF Inserter Interlock RAP Go to Flag 5. +5V is available at P/J601 between pins 3 and 4. Y↓N→+5V is available at P/J553 between pins 3 and 4. Y↓N→Install a new HVF control PWB, PL 11.157 Item 2. Check the connectors and harness between P/J553 and P/J601. Repair the harness as necessary. Go to Flag 5. +24V is available at P/J601 between pins 1 and pin 4. Y↓N→Install a new BM PWB, PL 11.166 Item 10. Go to Flag 6 +24V is available at P/J601 between pins 4 and 6. Y↓N→Go to the 311-300-00-171, 311-302-00-171, 311-303-00-171 Docking and Interlocks RAP. The +24V and +5V supplies are good. Go to SCP 5 Final actions. The +24V and +5V supplies are good. Go to SCP 5 Final actions. HVF Control PWB and BM PWB LEDs shows the LED s on the HVF PWB. These are: • LED 1 - red. Not used. • LED 2 - red. Not used. • LED 3 - red, flashing. This indicates the functioning of the CPU. When flashing at 2Hz, (every 1/2 second), the software is running normally. When flashing at about 1/4Hz, (every 4 seconds), this indicates that the software is encountering a code problem and a possible software upgrade is needed. If this LED is OFF, the CPU does not function and a new HVF control PWB is needed. • LED 4 - red. Not used. • LED 5 - red, toggling. This changes state whenever the paper is accelerated to 1,300 m/s. It is only used for paper that is longer than 220mm. • LED 6 - red, steady. When this is ON, a paper jam has been detected. It remains ON until the HVF successfully initializes. In all other cases this LED is OFF. • LED 7 - red. This LED is used during the machine production and is connected with the activity of the stacker nearly full sensor. • LED 8 - red, steady. This indicates that the HVF top cover, front door and docking interlocks are all closed and +24V is available at the HVF module. • LED 9 - red, steady. This indicates that the +5V supply is present in the HVF module. • LED 1 - red, steady. This indicates a fault or other abnormal status. • LED 2 - yellow, flashing at about 1Hz. This indicates that the software is operating in normal mode. In other modes, e.g., software downloading, the flashing rate is higher. • LED 3 - orange, steady. This indicates either: – that the tri-folder front door and top cover interlocks are closed, and +24V is available to the BM module or, if the tri-folder in not installed; – that the interlock cheater is present in PJ553 on the BM control PWB the logic cheater is present in PJ563 on the BM control PWB. • LED 19 - orange, steady. This indicates that the +24V supply is within voltage and current limits, and that the power limiting circuit has not been active for over a set time limit. • LED 5 - blue, steady. this indicates that the +5V supply is present in the BM module.