Description: Trail edge Late from Inverter Sensor RAP 310-135-00 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a simplex non invert sheet. 310-136-00 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a simplex inverted sheet. 310-137-00 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a duplex sheet side 1. 310-138-00 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a duplex sheet side 2. NOTE: The inverter sensor is only used on 65-90 ppm machines.
Remedy: NOTE: Ensure that the door interlock switch is cheated when checking +24V components. Enter dC330 code 010-105 inverter sensor, Q10-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q10-120. Refer to: • GP 11 How to Check a Sensor. • P/J61, IOT PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new inverter sensor, PL 10.12 Item 19. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 010-050 inverter nip solenoid, SOL10-050. Press Start. The solenoid energises. Y↓N→Go to Flag 2 (45 to 55ppm) or Flag 6 (65 to 90ppm). Check SOL10-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new inverter nip solenoid, PL 10.11 Item 6. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 010-045 inverter path solenoid, SOL 10-045. Press Start. The solenoid energizes. Y↓N→Go to Flag 3 (45 to 55ppm) or Flag 7 (65 to 90ppm). Check SOL 10-045. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new inverter path solenoid, PL 10.11 Item 14. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. 65-90 ppm only. Enter dC330 code 010-055 tri-roll nip split solenoid, SOL 10-055. Press Start. The solenoid energizes. Y↓N→Go to Flag 5. Check SOL 10-055. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J61, IOT PWB • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new tri-roll nip split solenoid, PL 10.14 Item 1. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 010-030 inverter motor, MOT10-030. Press Start. The jam clearance knob, 2B, PL 10.15 Item 13, is stationary and the motor can be heard. Y↓N→The jam clearance knob, 2B, PL 10.15 Item 13, rotates counterclockwise. Y↓N→Go to Flag 4. Check MOT10-030. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB • P/J45, P/J55 inverter motor driver PWB • 301G +24V Distribution RAP • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Inverter motor, PL 10.14 Item 13. • Inverter motor driver PWB, PL 10.11 Item 22. If the fault remains, perform the OF7 IOT PWB Diagnostics RAP. Install a new inverter motor driver PWB, PL 10.11 Item 22. Check the following components, refer to GP 7: • Idler roll, PL 10.12 Item 15. • Upper baffle, PL 10.12 Item 22. • Decurler roll, PL 10.13 Item 8. • Nip split shaft assembly, PL 10.11 Item 4. • The drive gear on the fuser module, PL 10.10 Item 1. • The fuser drive gear on the main drives module, PL 40.12 Item 10. If the fault remains, the +24V supply from the LVPS may be faulty. Perform the 301L LVPS Checkout RAP.