Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 311A-171 — Xerox WorkCentre 5855

Code: 311A-171

Description: HVF Power Distribution RAP The HVF has an integral power supply providing +24V and +5V supplies to the HVF PWB and HVF BM PWB. The AC power for the HVF power supply comes from the LVPS and base module of the machine.
Remedy: Refer to HVF Control PWB and BM PWB LEDs to identify the status of the PWBs. Close or cheat all the HVF BM interlocks. The HVF BM performs a mechanical reset. Y↓N→Go to Flag 2. +5V is available at P/J113 between pins 1 and 2. Y↓N→+5V is available at T001 on the HVF power supply module between pins 4 and 8. Y↓N→Go to Flag 1. ACL is available at PJ22 on the LVPS and base module between pins 1 and 2. Y↓N→Go to the 301C AC Power RAP and check the AC output voltages. Switch off the machine, GP 14. Disconnect all PJs on the HVF Control PWB except P/J111 and P/J113. Switch on the machine, GP 14. Go to Flag 2. +5V is available at T001 on the HVF power supply module between pins 4 and 8. Y↓N→Install a new HVF power supply module, PL 11.157 Item 1. NOTE: Before each PJ is reconnected, switch off the machine, GP 14. The HVF has a short circuit. Reconnect each PJ one at a time until short circuit is found. When the short circuit is found, repair the harness or install new components as necessary. Disconnect P/J113. Go to Flag 2. +5V is available at the harness end of P/J113 between pins 1 and 2. Y↓N→Check the connectors and harness between T001 and P/J113. Repair the harness as necessary. Install a new HVF control PWB, PL 11.157 Item 2. Go to Flag 2. +24V is available at P/J111 between pins 1 and 4. Y↓N→+24V is available at T001 between pins 1 and 5. Y↓N→Install a new HVF power supply module, PL 11.157 Item 1 Check the in-line fuse (10A), and as necessary install a new fuse PL 11.157 Item 5. Check the connectors and harness between T001 and PJ111. Repair the harness as necessary. Go to Flag 3. +24V is available at P/J111 between pins 1 and 4, between pins 2 and 5 and between pins 3 and 6. Y↓N→Go to the 311-300-00-171, 311-302-00-171, 311-303-00-171 Docking and Interlocks RAP. Go to Flag 4. +5V is available at P/J559 between pins 4 and 5. Y↓N→+5V is available at P/J132 between pins 1 and 2. Y↓N→Install a new HVF control PWB, PL 11.157 Item 2. Check the connectors and harness between P/J132 and P/J559. Repair the harness as necessary. Go to Flag 4. +24V is available at P/J559 between pins 1 and 2. Y↓N→+24V is available at P/J131 between pins 1 and 2. Y↓N→Install a new HVF control PWB, PL 11.157 Item 2. Check the connectors and harness between P/J559 and P/J131. Repair the harness as necessary. If a inserter is installed, go to P/J703. +24V is available between P/J703 pin 1 and P/ J111 pin 1. Y↓N→Go to 311-306-00-171, 311-309-00-171 HVF Inserter Interlock RAP Go to Flag 5. +5V is available at P/J601 between pins 3 and 4. Y↓N→+5V is available at P/J553 between pins 3 and 4. Y↓N→Install a new HVF control PWB, PL 11.157 Item 2. Check the connectors and harness between P/J553 and P/J601. Repair the harness as necessary. Go to Flag 5. +24V is available at P/J601 between pins 1 and pin 4. Y↓N→Install a new BM PWB, PL 11.166 Item 10. Go to Flag 6 +24V is available at P/J601 between pins 4 and 6. Y↓N→Go to the 311-300-00-171, 311-302-00-171, 311-303-00-171 Docking and Interlocks RAP. The +24V and +5V supplies are good. Go to SCP 5 Final actions. The +24V and +5V supplies are good. Go to SCP 5 Final actions. HVF Control PWB and BM PWB LEDs shows the LED s on the HVF PWB. These are: • LED 1 - red. Not used. • LED 2 - red. Not used. • LED 3 - red, flashing. This indicates the functioning of the CPU. When flashing at 2Hz, (every 1/2 second), the software is running normally. When flashing at about 1/4Hz, (every 4 seconds), this indicates that the software is encountering a code problem and a possible software upgrade is needed. If this LED is OFF, the CPU does not function and a new HVF control PWB is needed. • LED 4 - red. Not used. • LED 5 - red, toggling. This changes state whenever the paper is accelerated to 1,300 m/s. It is only used for paper that is longer than 220mm. • LED 6 - red, steady. When this is ON, a paper jam has been detected. It remains ON until the HVF successfully initializes. In all other cases this LED is OFF. • LED 7 - red. This LED is used during the machine production and is connected with the activity of the stacker nearly full sensor. • LED 8 - red, steady. This indicates that the HVF top cover, front door and docking interlocks are all closed and +24V is available at the HVF module. • LED 9 - red, steady. This indicates that the +5V supply is present in the HVF module. • LED 1 - red, steady. This indicates a fault or other abnormal status. • LED 2 - yellow, flashing at about 1Hz. This indicates that the software is operating in normal mode. In other modes, e.g., software downloading, the flashing rate is higher. • LED 3 - orange, steady. This indicates either: – that the tri-folder front door and top cover interlocks are closed, and +24V is available to the BM module or, if the tri-folder in not installed; – that the interlock cheater is present in PJ553 on the BM control PWB the logic cheater is present in PJ563 on the BM control PWB. • LED 19 - orange, steady. This indicates that the +24V supply is within voltage and current limits, and that the power limiting circuit has not been active for over a set time limit. • LED 5 - blue, steady. this indicates that the +5V supply is present in the BM module.

← Xem tất cả mã lỗi Xerox WorkCentre 5855

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie