Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 374-100-00 — Xerox WorkCentre 5855

Code: 374-100-00

Description: Tray 4 Elevator Lift Failure RAP 374-100-00 Tray 4 stack height sensor did not actuate within the correct time after the elevator motor turned on. NOTE: Rapid closure of tray 3 when tray 4 is being elevated may cause this fault.
Remedy: Enter dC330 code 074-300 tray 4 home sensor, Q74-300. Press Start. Pull out tray 4, then push fully home. The display changes. Y↓N→Go to Flag 1. Check Q74-300. Refer to: • GP 11 How to Check a Sensor. • P/J3, HCF control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 home sensor, PL 70.21 Item 4. • HCF control PWB, PL 70.21 Item 2. Enter dC330 code 074-330 tray 4 stack height sensor, Q74-330. Press Start. Pull out tray 4. Manually actuate the stack height sensor on the paper feed assembly. The display changes. Y↓N→Go to Flag 2. Check Q74-330. Refer to: • GP 11 How to Check a Sensor. • P/J3, HCF control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 stack height sensor, PL 80.33 Item 6. • HCF control PWB, PL 70.21 Item 2. Disconnect P/J12 on the HCF control PWB. Connect a service meter between pin 1 and pin 2 on the wiring side of the connector. Continuity is measured when the stack limit switch is deactuated and open circuit is measured when the switch is actuated. Y↓N→Go to Flag 3. Check the tray 4 over elevate switch. Refer to: • GP 13 How to Check a Switch. • P/J12, HCF control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 over elevate switch, PL 80.33 Item 9. • HCF control PWB, PL 70.21 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT74-010 is run in service mode. Enter dC330 code 074-010 tray 4 elevator motor, MOT74-010. Pull out tray 4. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT74-010. Refer to: • GP 10 How to Check a Motor. • P/J14, HCF control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 elevator motor, PL 70.21 Item 1. • HCF control PWB, PL 70.21 Item 2. Perform the following: • Check the elevator cables, PL 70.18 Item 4, PL 70.18 Item 5 and PL 70.18 Item 7. • Check elevator drives gear coupling, PL 70.19 Item 10. If the fault remains, go to 373B Tray 3 or Tray 4 Out of Paper RAP.

← Xem tất cả mã lỗi Xerox WorkCentre 5855

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie