Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 381-104-00, 381-114-00 — Xerox WorkCentre 5855

Code: 381-104-00, 381-114-00

Description: Tray 4 Misfeed RAP 381-104-00 The lead edge of the paper failed to actuate the tray HCF exit sensor within the correct time after feeding paper from tray 4. 381-114-00 The HCF exit sensor did not de-actuate within the correct time after the sensor was actuated.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 081-104 tray 4 feed sensor, Q81-104. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q81-104. Refer to: • GP 11 How to Check a Sensor. • P/J3, HCF control PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 feed sensor, PL 80.33 Item 3. • HCF control PWB, PL 70.21 Item 2. Enter dC330 code 081-045 HCF transport motor, MOT81-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT81-045. Refer to: • GP 10 How to Check a Motor. • P/J6, HCF control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • HCF transport motor, PL 80.36 Item 13. • HCF control PWB, PL 70.21 Item 2. Observe the tray 3 and 4 transport roll, PL 80.32 Item 4 and the takeaway roll assembly, PL 80.36 Item 2. The transport roll and takeaway roll rotate. Y↓N→Check the following: • Drive coupling, PL 80.36 Item 7. • Drive belt, PL 80.36 Item 6. • Transport gear pulley, PL 80.36 Item 12. • Check the idler shaft of the transport gear pulley. If the weld of the idler shaft on the HCF frame has broken, install an idle gear shaft spare kit, PL 31.14 Item 7/ CAUTION To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT81- 040 is run in service mode. Enter dC330 code 081-040 tray 4 feed motor, MOT81-040. Pull out the tray. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT81-040. Refer to: • GP 10 How to Check a motor. • P/J5, HCF control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 feed motor, PL 80.33 Item 10. • HCF control PWB, PL 70.21 Item 2. Locate the tray 4 feed clutch. Enter dC330 code 081-040 tray 4 feed motor, MOT81- 040, stack the code 081-034 tray 4 feed clutch, CL81-034. Pull out tray 4. Observe the tray 4 feed and nudger rolls. Press Start. The rolls rotate. Y↓N→Go to Flag 4. Check CL81-034. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, HCF control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 paper feed assembly, PL 80.33 Item 1. • HCF control PWB, PL 70.21 Item 2. Perform the following: • Clean the feed roll, nudger roll and retard roll using a cloth dampened with water. • Check the feed roll, retard roll and nudger roll for wear. If necessary install a new feed/ nudger/retard roll spares kit, PL 31.13 Item 14. • Perform the following adjustments: – ADJ 80.3 Tray 3 and Tray 4 Retard Roll Pressure. – ADJ 80.4 Tray 3 and Tray 4 Nudger Roll Pressure. • Check the tray 4 stack height sensor actuator on the feed assembly, PL 80.33. • Check the tray is level. 1. Pull out tray 4 and remove all of the paper from the tray. 2. Remove the tray 4 front cover. 3. Manually elevate the tray to the top of its travel by rotating the elevator cable drum at the front of the tray. 4. At the three locations where the metal paper tray protrude through the plastic outer frame of tray 4, check that the top surface of the metal paper tray is the same distance from the inside top of the slots. 5. If the tray is not level then install new elevator cables, PL 70.18. • Check the tray 4 paper tray guide for paper cut damage. If necessary, install new components, PL 70.19 Item 6.

← Xem tất cả mã lỗi Xerox WorkCentre 5855

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie