Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 081-106 PFP feed sensor, Q81-106. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q81-106. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 6 control PWB • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 6 feed sensor, PL 80.45 Item 6. • Tray 6 control PWB, PL 70.68 Item 8. Enter dC330 code 081-060 PFP feed motor, MOT81-060. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT81-060. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 6 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 6 feed motor, PL 80.40 Item 3. • Tray 6 control PWB, PL 70.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 80.40 Item 5. • Gear 30T bearing, PL 80.40 Item 21. • Gear, PL 80.45 Item 14. The feed roll rotates Y↓N→Check the one way coupling, feed roll and clutch. Install new components as necessary: • One way coupling, PL 80.45 Item 4. • Clutch, PL 80.45 Item 13. • Feed roll, PL 80.45 Item 12. The nudger roll rotates Y↓N→Check the nudger roll and the one way gear. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way gear, PL 80.45 Item 3. • Drive belt, PL 80.40 Item 7. • Nudger roll, PL 80.45 Item 10. The retard roll rotates Y↓N→Check the retard roll, retard clutch and clutch. Install new components as necessary: • Retard clutch, PL 80.47 Item 11. • Clutch, PL 80.47 Item 7. • Retard roll, PL 80.47 Item 2. Enter dC330 code 081-065 PFP transport motor, MOT81-065. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT81-065. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 6 control PWB • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 6 transport motor, PL 80.40 Item 2. • Tray 6 control PWB, PL 70.68 Item 8. Run the motor for 30 seconds. The motor runs at a constant speed, without slowing. Y↓N→Install a new tray 6 transport motor, PL 80.40 Item 2. The take away roller rotates. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 80.40 Item 7. • One way pulley clutch, PL 80.47 Item 4. • Take away roller, PL 80.47 Item 5. Enter dC330 code 081-110 PFP wait point sensor, Q81-110. Press Start. NOTE: For trays 1 to 6, the input code 081-100 wait sensor is used to check the operation of the wait sensor. In addition tray 6 uses the input code 081-110 PFP wait point sensor, to check the paper present signal from the IOT PWB to the tray 6 control PWB. Open the bypass tray and left door assembly. Manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 081-100 wait sensor, Q81-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q81-100. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 301D +3.3V Distribution RAP. • 301B 0V Distribution RAP. If necessary install a new wait sensor, PL 80.15 Item 3. If the problem persists, perform the OF7 IOT PWB Diagnostics RAP. Go to Flag 5. Manually actuate Q81-100. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the tray 6 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 6 control PWB. If necessary install a new tray 6 control PWB, PL 70.68 Item 8. If the problem persists, perform the OF7 IOT PWB Diagnostics RAP. Perform the steps that follow: • ADJ 70.5, Tray 6 Stack Height Sensor and Retard Shield. • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 80.45 Item 21.