Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 311-030-00-110, 311-334-00-110, 311-335-00-110, 311-336-00-110 — Xerox WorkCentre 5865

Code: 311-030-00-110, 311-334-00-110, 311-335-00-110, 311-336-00-110

Description: Bin 1 Movement Failure RAP 311-030-00-110 Bin 1 fails to move. 311-334-00-110 Bin 1 has reached the upper limit of travel. 311-335-00-110 Bin 1 has reached the lower limit of travel. 311-336-00-110 Bin 1 is not at the home position. NOTE: The home position of bin 1 is when bin 1 is actuating the bin 1 lower level sensor. See the final actions at the end of the procedure. Three sensors and two switches monitor the level of paper in bin 1 and the position of the tray: • The bin 1 upper level sensor, the highest of two sensors that detect the top of the paper stack in bin 1, or the empty bin 1. • The bin 1 90% full sensor detects when the tray has descended to a position where the tray is 90% full. • The bin 1 lower level sensor, the lowest of two sensors that detects when paper is removed from bin 1. • Bin 1 upper limit switch, S11-334. • Bin 1 lower limit switch, S11-335.
Remedy: NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. Remove the 2K LCSS rear cover. Enter dC330 code 011-336, bin 1 motor encoder sensor Q11-336. Slowly rotate the encoder disk by hand. The display changes. Y↓N→Go to Flag 2. Check Q11-336. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J304, 2K LCSS PWB. • 311D-110 2K LCSS Power Distribution RAP. Install new components as necessary: • Bin 1 motor encoder sensor, PL 11.10 Item 11. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 011-033, bin 1 elevator motor, MOT11-030. Bin 1 cycles down and up. Y↓N→Go to Flag 1. Check MOT11-030. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 10 How to Check a Motor. • P/J318, 2K LCSS PWB. • 311D-110 2K LCSS Power Distribution RAP. Install new components as necessary: • Bin 1 elevator motor, PL 11.10 Item 8 • 2K LCSS PWB, PL 11.26 Item 1., enter dC330 code 011-332. Actuate the bin 1 upper level sensor, Q11-332. The display changes. Y↓N→Go to Flag 4. Check Q11-332. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J314, 2K LCSS PWB. • 311D-110 2K LCSS Power Distribution RAP. •-110 2K LCSS Un-docking. Install new components as necessary: • Bin 1 upper level sensor, PL 11.12 Item 3. • 2K LCSS PWB, PL 11.26 Item 1., enter dC330, code 011-333. Actuate the bin 1 lower level sensor, Q11-333. The display changes. Y↓N→Go to Flag 3. Check Q11-333. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J314, 2K LCSS PWB. • 311D-110, 2K LCSS Power Distribution RAP. •-110 2K LCSS Un-docking. Install new components as necessary: • Bin 1 lower level sensor, PL 11.12 Item 3. • 2K LCSS PWB, PL 11.26 Item 1.. Enter dC330 code 011-334. Actuate the bin 1 upper limit switch, S11-334. The display changes. Y↓N→Go to Flag 5. Check S11-334. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 13 How to Check a Switch. • P/J315, 2K LCSS PWB. • 311D-110 2K LCSS Power Distribution RAP. Install new components as necessary: • Bin 1 upper limit switch, PL 11.10 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 011-335. Actuate the bin 1 lower limit switch, S11-335. The display changes. Y↓N→Go to Flag 6. Check S11-335. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 13 How to Check a Switch. • P/J317, 2K LCSS PWB. • 311D-110 2K LCSS Power Generation RAP. •-110 2K LCSS Un-docking. Install new components as necessary: • Bin 1 lower limit switch, PL 11.12 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 011-331. Actuate the bin 1 90% full sensor, Q11-331. The display changes. Y↓N→Go to Flag 7. Check Q11-331. Refer to: • 311G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. • P/J316, 2K LCSS PWB. • 311D-110, 2K LCSS Power Distribution RAP. Install new components as necessary: • Bin 1 90% full sensor, PL 11.10 Item 5. • 2K LCSS PWB, PL 11.26 Item 1. As final actions, check the following sequence of operation: • When bin 1 is empty and at the top of it’s travel, the bin 1 lower level sensor, Q11-333 is actuated by the edge of the tray and the bin 1 upper level sensor, Q11-332 is de-actuated. • Paper is delivered to the tray until the bin 1 upper level sensor, Q11-332 is actuated. • The motor lowers the tray until the bin 1 upper level sensor, Q11-332 is de-actuated. • As the tray is lowered to accommodate the increase in stack height, the bin 1 lower level sensor, Q11-333 is held actuated by the stack rear edge. • When the tray is emptied, the tray returns to the home position; the bin 1 lower level sensor, Q11-333 is de-actuated and the tray is elevated until both the bin 1 lower level sensor, Q11-333 and bin 1 upper level sensor, Q11-332 are made. The tray is then lowered until the bin 1 upper level sensor, Q11-332 is just cleared. In the home position the bin one upper limit switch, S11-334 is also actuated.

← Xem tất cả mã lỗi Xerox WorkCentre 5865

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie