Description: Inserter Paper Jam RAP 311-191-00-171 The leading edge is late arriving at the inserter standby sensor. 311-193-00-171 The trailing edge is late leaving the inserter standby sensor. 311-194-00-171 The leading edge is late arriving at the inserter TE sensor. 311-196-00-171 The trailing edge is late leaving the inserter TE sensor. Fault code 311-191-00 may also be generated where a fault in the inserter causes jamming in the IOT.
Remedy: Enter dC330 code 011-155. Manually actuate the inserter TE sensor, Q11-155. The display changes. Y↓N→Go to Flag 1 and Flag 2. Check Q11-155. Refer to: • GP 11, How to Check a Sensor. • P/J6, P/J4, Inserter PWB. • P/J701, HVF Control PWB • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter TE sensor, PL 11.179 Item 11. • Inserter PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Measure the voltage of pin 2 of P/J11. Manually actuate the acceleration sensor. The voltage changes. Y↓N→Go to Flag 3 and Flag 4. Check the sensor. Refer to: • GP 11, How to Check a Sensor. • P/J6, P/J4, Inserter PWB. • P/J701, HVF Control PWB Install new components as necessary: • Acceleration sensor, PL 11.175 Item 10. • Inserter PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Measure the voltage at pin 2 of P/J702 on the HVF PWB. Open the front door and open 8a jam clearance guide. Manually actuate the inserter standby sensor with a sheet of paper. The voltage changes. Y↓N→Go to Flag 5. Check the sensor. Refer to: • GP 11, How to Check a Sensor. • P/J702, HVF Control PWB • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter standby sensor, PL 11.156 Item 2. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-077, to energize the inserter clutch, CL11-077. CL11-077 energizes. Y↓N→Go to Flag 6 (W/O TAG V-001) or Flag 10 (W/TAG V-001) and Flag 7. Check CL11-077. Refer to: • GP 12, How to Check a Solenoid or Clutch. • P/J13, P/J5, Inserter PWB. • P/J703, HVF Control PWB • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter clutch, PL 11.179 Item 3. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-078 to run the inserter motor, MOT11-078. MOT11-078 runs. Y↓N→Go to Flag 8 and Flag 9. Check MOT11-078. Refer to: • GP 10 How to Check a Motor. • P/J701, HVF Control PWB • P/J4, Inserter PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter motor, PL 11.181 Item 1. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Perform SCP 5 Final Actions.