Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 311-371-00-171 ... 311-377-00-171 — Xerox WorkCentre 5875

Code: 311-371-00-171 ... 311-377-00-171

Description: HVF Stapler Position and Priming RAP 311-371-00-171 The stapler did not move from the home position. 311-372-00-171 The stapler did not return to the home position. 311-373-00-171 The stapler did not enter the mid home position. 311-374-00-171 The stapler did not leave the mid home position. 311-375-00-171 The stapler jaw did not enter the home position. 311-376-00-171 The stapler jaw did not leave the home position. 311-377-00-171 A stapler priming failure was detected.
Remedy: Enter dC330 code 011-053 to run the stapler unit motor, MOT11-053 and send it to the inboard end of its travel. The motor runs. Y↓N→Go to Flag 5. Check MOT11-053. Refer to: • GP 10 How to Check a Motor. • P/J801, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Stapler assembly, PL 11.140 Item 14. • HVF control PWB, PL 11.157 Item 2. With the stapler unit still at the inboard end, enter dC330 code 011-360, stapler home sensor. Manually activate the stapler home sensor, Q11-360. The display changes. Y↓N→Go to Flag 1. Check Q11-360. Refer to: • GP 11 How to Check a Sensor. • P/J301, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Stapler assembly, PL 11.140 Item 14. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-054 to send the stapler unit to the outboard end of the machine. Enter code 011-175, stapler unit mid home sensor. Manually activate the stapler unit mid home sensor, Q11-175. The display changes. Y↓N→Go to Flag 4. Check Q11-373. Refer to: • GP 11 How to Check a Sensor. • P/J301, HVF Control PWB. • 311A-171 HVF Power Distribution RAP Install new components as necessary: • Stapler assembly, PL 11.140 Item 14. • HVF control PWB, PL 11.157 Item 2. Place two sheets of paper in the stapler jaws. Raise the finisher top cover., lower the paper pusher fully down and lower the top cover. Enter dC330 code 011-050 to run the staple head motor, MOT11-050. MOT11-050 runs. Y↓N→Go to Flag 6. Check the wiring and repair as necessary. Check the stapler gate safety switch. Refer to: • GP 13 How to Check a Switch. • P/J304, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Sensor assembly, PL 11.145 Item 22. • Stapler assembly, PL 11.140 Item 14. • HVF control PWB, PL 11.157 Item 2. With the paper still in place, re-enter the code 011-050 to run the staple head motor, MOT11-050. MOT11- 050 runs. Y↓N→Go to Flag 2. Check MOT11-050. Refer to: • GP 10 How to Check a Motor. • P/J801, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Stapler assembly, PL 11.140 Item 14. • HVF control PWB, PL 11.157 Item 2. If the stapler is now working satisfactorily, perform SCP 5 Final Actions. If necessary, continue with this RAP. Remove the stapled paper and raise the paper pusher fully upwards. Go to Flag 3. +5V is available at T502 between pins 1 and 4, also between pin 1 and 7 on the staple head. Y↓N→Check the wiring between P/J T502 and P/J301. The wiring is good. Y↓N→Repair the wiring or install a new stapler harness and P-clip assembly, PL 11.140 Item 25. Install a new HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-364 actuate the stapler priming sensor, Q11-364, by removing and installing the staple cartridge. The display changes. Y↓N→Check for a change in signal level at P/J301 pin 9 when Q11-364 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J301 pin 9 and the staple head unit. The wiring is good. Y↓N→Repair the wiring or install a new stapler harness and P-clip assembly, PL 11.140 Item 25 as necessary. Install a new stapler assembly, PL 11.140 Item 14. Install a new HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-363 actuate the stapler cartridge sensor, Q11-363, by removing and installing the staple cartridge. The display changes. Y↓N→Check for a change in signal level at P/J301 pin 10 when Q11-363 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J301 pin 10 and the staple head unit. The wiring is good. Y↓N→Repair the wiring or install a new stapler harness and P-clip assembly, PL 11.140 Item 25 as necessary. Install a new stapler assembly, PL 11.140 Item 14. Install a new HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-360 to monitor the staple home sensor Q11-360, stack the code 011- 050 to cycle the staple head. The display changes. Y↓N→Go to Flag 3. Check for a change in signal level at P/J301 pin 12, while code 011-050 is running. The signal level changes. Y↓N→Check the wiring between P/J301 pin 12 and the staple head unit. The wiring is good. Y↓N→Repair the wiring or install a new stapler harness and P-clip assembly, PL 11.140 Item 25 as necessary. Install a new stapler assembly, PL 11.140 Item 14. Install a new HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-362, actuate the low staples sensor, Q11-362, by removing and installing the staple cartridge. The display changes. Y↓N→Go to Flag 3. Check for a change in signal level at P/J301 pin 13 when Q11-362 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J301 pin 13 and the staple head unit. The wiring is good. Y↓N→Repair the wiring or install a new stapler harness and P-clip assembly, PL 11.140 Item 25 as necessary. Install a new stapler assembly, PL 11.140 Item 14. Install a new HVF control PWB, PL 11.157 Item 2. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components.

← Xem tất cả mã lỗi Xerox WorkCentre 5875

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie