Description: HVF Bin 1 Position RAP 311-460-00-171 Bin 1 motor has stalled. 311-461-00-171 Bin 1 did not actuate the bin 1 upper level sensor during stacking. 311-462-00-171 Bin 1 did not leave the bin 1 upper level sensor during stacking.
Remedy: NOTE: The bin 1 90% full sensor, Q11-331, and the bin 1 lower limit switch are mounted on the same bracket. This bracket can be in either of two positions. It is in the upper position, only when a tri-folder module is installed. NOTE: The bin 1 upper level sensor controls the height of the tray during normal use. The sensor is in two parts: the transmitter at the front of the tray and the receiver at the rear of the tray. Only the LED of the front sensor is used and only the light sensitive transistor of the rear sensor is used. Refer to Flag 3 and Flag 4. shows the location of the components. Place about one centimeter thickness of paper on the bin 1 tray. Switch off, then switch on the machine, GP 14. The bin 1 tray moves during initialization. Y↓N→If the tray is not at the upper limit, enter dC330 code 011-334, bin 1 upper limit switch, S11-334. Manually actuate S11-334. The display changes. Y↓N→Go to Flag 5. Check the wiring and repair as necessary. Check S11-334. Refer to: • GP 13 How to Check a Switch. • P/J602, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Bin 1 upper limit switch, PL 11.135 Item 7. • HVF control PWB, PL 11.157 Item 2. If the tray is not at the lower limit, enter dC330 code 011-335, bin 1 lower limit switch, S11- 335. Manually actuate S11-335. The display changes. Y↓N→Go to Flag 6. Check the wiring and repair as necessary. Check S11-335. Refer to: • GP 13 How to Check a Switch. • P/J602, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Bin 1 lower limit switch, PL 11.135 Item 7. • HVF control PWB, PL 11.157 Item 2. Go to Flag 1. Check the wiring and repair as necessary. Check the bin 1 elevator motor, 11-030. Refer to: • GP 10 How to Check a Motor. • P/J202, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Bin 1 elevator motor, PL 11.135 Item 10. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-182, bin 1 encoder sensor, Q11-182. Turn the bin 1 encoder wheel. The display changes. Y↓N→Go to Flag 2. Check the wiring and repair as necessary. Check Q11-182. Refer to: • GP 11 How to Check a Sensor. • P/J601, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Bin 1 encoder sensor, PL 11.135 Item 3. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-332, bin 1 upper level sensor, Q11-332. Remove the paper from the tray. Actuate the sensor by breaking the light beam from the front transmitter to the rear receiver. The display changes. Y↓N→Go to Flag 3 and Flag 4. Check the wiring and repair as necessary. Check the two parts of Q11-332. Refer to: • GP 11 How to Check a Sensor. • P/J601 and P/J901, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Bin 1 upper level sensor (transmitter), PL 11.140 Item 20. • Bin 1 upper level sensor (receiver), PL 11.140 Item 16. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 011-331, bin 1 90% full sensor, Q11-331. Actuate the sensor using a piece of paper. The display changes. Y↓N→Go to Flag 7. Check the wiring and repair as necessary. Check Q11-331. Refer to: • GP 11 How to Check a Sensor. • P/J601, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Bin1 90% full sensor, PL 11.135 Item 3. • HVF control PWB, PL 11.157 Item 2. Lower the bin 1 tray by pressing the PTU switch, or by entering dC330 code 011-032, bin1 elevator motor down. Enter the dC330 code 011-196, bin 1 rear wall sensor, Q11-196. Actuate Q11-196 using a sheet of paper. The display changes. Y↓N→Go to Flag 8. Check the wiring and repair as necessary. Check Q11-196. Refer to: • GP 11 How to Check a Sensor. • P/J403, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Bin 1 rear wall sensor, PL 11.140 Item 17. • HVF control PWB, PL 11.157 Item 2. If the fault is random and bin 1 has an erratic up / down movement and poor stacking. Check that the bin 1 rear wall sensor is clean. The sensor is clean. Y↓N→Clean the bin 1 rear wall sensor. Use a brush to remove paper dust from the sensor and the plastic surround. Then use a damp cloth to clean the sensor and plastic surround. Perform SCP 5 Final Actions.