Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 381-115-00B, 381-117-00B — Xerox WorkCentre 5875

Code: 381-115-00B, 381-117-00B

Description: Tray 6 Misfeed RAP (65-90 ppm)
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 081-106 PFP feed sensor, Q81-106. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q81-106. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 6 control PWB • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 6 feed sensor, PL 80.45 Item 6. • Tray 6 control PWB, PL 70.68 Item 8. Enter dC330 code 081-060 PFP feed motor, MOT81-060. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT81-060. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 6 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 6 feed motor, PL 80.40 Item 3. • Tray 6 control PWB, PL 70.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 80.40 Item 5. • Gear 30T bearing, PL 80.40 Item 21. • Gear, PL 80.45 Item 14. The feed roll rotates Y↓N→Check the one way coupling, feed roll and clutch. Install new components as necessary: • One way coupling, PL 80.45 Item 4. • Clutch, PL 80.45 Item 13. • Feed roll, PL 80.45 Item 12. The nudger roll rotates Y↓N→Check the nudger roll and the one way gear. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way gear, PL 80.45 Item 3. • Drive belt, PL 80.40 Item 7. • Nudger roll, PL 80.45 Item 10. The retard roll rotates Y↓N→Check the retard roll, retard clutch and clutch. Install new components as necessary: • Retard clutch, PL 80.47 Item 11. • Idler roll, PL 80.47 Item 7. • Retard roll, PL 80.47 Item 2. Enter dC330 code 081-065 PFP transport motor, MOT81-065. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT81-065. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 6 control PWB • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 6 transport motor, PL 80.40 Item 2. • Tray 6 control PWB, PL 70.68 Item 8. Run the motor for 30 seconds. The motor runs at a constant speed, without slowing. Y↓N→Install a new tray 6 transport motor, PL 80.40 Item 2. The take away roller rotates. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 80.40 Item 7. • One way pulley clutch, PL 80.47 Item 4. • Take away roller, PL 80.47 Item 5. Enter dC330 code 081-100 PFP wait point sensor, Q81-100. Press Start. NOTE: For trays 1 to 6, the input code 081-100 wait sensor is used to check the operation of the wait sensor. In addition tray 6 uses the input code 081-110 PFP wait point sensor, to check the paper present signal from the IOT PWB to the tray 6 control PWB. Open the bypass tray and left door assembly. Manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 081-100 wait sensor, Q81-100. Press Start. Manually actuate Q81-100. The display changes. Y↓N→Go to Flag 2. Check Q81-100. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 301E +5V Distribution RAP. • 301B 0V Distribution RAP. If necessary install a new wait sensor, PL 70.30 Item 24. If the problem persists, perform the OF7 IOT PWB Diagnostics RAP. Go to Flag 5. Manually actuate the wait sensor. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the Tray 6 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 6 control PWB. If necessary install a new tray 6 control PWB, PL 70.68 Item 8. If the problem persists, perform OF7 IOT PWB Diagnostics RAP. Perform the steps that follow: • ADJ 70.5, Tray 6 Stack Height Sensor and Retard Shield. • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 80.45 Item 21.

← Xem tất cả mã lỗi Xerox WorkCentre 5875

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie