Description: LVF BM Bin 1 Movement Failure RAP 311-030-00-150 Bin 1 fails to move. 311-334-00-150 Bin 1 has reached the upper limit of travel. 311-335-00-150 Bin 1 has reached the lower limit of travel. 311-336-00-150 Bin 1 is not at the home position. NOTE: The home position of bin 1 is when bin 1 is actuating the bin 1 lower level sensor. See the final actions at the end of the procedure. Three sensors and two switches monitor the level of paper in bin 1 and the position of the tray: • The bin 1 upper level sensor, the highest of two sensors that detect the top of the paper stack in bin 1, or the empty bin 1. • The bin 1 90% full sensor detects when the tray has descended to a position where the tray is 90% full. • The bin 1 lower level sensor, the lowest of two sensors that detects when paper is removed from bin 1. • Bin 1 upper limit switch, S11-334. • Bin 1 lower limit switch, S11-335.
Remedy: NOTE: All LVF BM interlocks must be made to supply +24V to the motors. Remove the LVF BM rear cover assembly. Enter dC330 code 011-336, bin 1 motor encoder sensor Q11-336, slowly rotate the encoder disk by hand. The display changes. Y↓N→Go to Flag 2. Check Q11-336. Refer to: • GP 11 How to Check a Sensor. • P/J304, LVF PWB. • 311D-150 LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 motor encoder sensor, PL 11.58 Item 9. • LVF PWB, PL 11.90 Item 8. Enter dC330 code 011-033, bin 1 elevator motor, MOT11-030. Bin 1 cycles down and up. Y↓N→Go to Flag 1. Check MOT11-030. Refer to: • GP 10 How to Check a Motor. • P/J318, LVF PWB. • 311D-150 LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 elevator motor, PL 11.58 Item 7 • LVF PWB, PL 11.90 Item 8., enter dC330, code 011-332. Actuate the bin 1 upper level sensor Q11-332. The display changes. Y↓N→Go to Flag 4. Check Q11-332. Refer to: • GP 11 How to Check a Sensor. • P/J314, LVF PWB • 311D-150 LVF BM Power Distribution RAP. •-150 LVF BM Un-docking. Repair or install new components as necessary: • Bin 1 upper level sensor, PL 11.60 Item 3. • LVF PWB, PL 11.90 Item 8., enter dC330, code 011-333. Actuate the bin 1 lower level sensor Q11-333. The display changes. Y↓N→Go to Flag 3. Check Q11-333. Refer to: • GP 11 How to Check a Sensor. • P/J314, LVF PWB. • 311D-150, LVF BM Power Distribution RAP. •-150 LVF BM Un-docking. Repair or install new components as necessary: • Bin 1 lower level sensor Q11-333, PL 11.60 Item 3. • LVF PWB, PL 11.90 Item 8.. Enter dC330 code 011-334. Actuate the bin 1 upper limit switch, S11-334. The display changes. Y↓N→Go to Flag 5. Check S11-334. Refer to: • GP 13 How to Check a Switch. • P/J315, LVF PWB. • 311D-150 LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 upper limit switch, PL 11.58 Item 3. • LVF PWB, PL 11.90 Item 8. Enter dC330 code 011-335, actuate the bin 1 lower limit switch, S11-335. The display changes. Y↓N→Go to Flag 6. Check S11-335. Refer to: • GP 13 How to Check a Switch. • P/J314, LVF PWB. • 311D-150 LVF BM Power Distribution RAP. •-110 LVF BM Un-docking. Repair or install new components as necessary: • Bin 1 lower limit switch, PL 11.60 Item 1. • LVF PWB, PL 11.90 Item 8. Enter dC330 code 011-331, actuate the bin 1 90% full sensor, Q11-331. The display changes. Y↓N→Go to Flag 7. Check Q11-331. Refer to: • GP 11 How to Check a Sensor. • P/J316, LVF PWB. • 311D-150, LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 90% full sensor Q11-331, PL 11.58 Item 5. • LVF PWB, PL 11.90 Item 8. As final actions, check the following sequence of operation: • When bin 1 is empty and at the top of it’s travel, the bin 1 lower level sensor, Q11-333 is actuated by the edge of the tray and the bin 1 upper level sensor, Q11-332 is de-actuated. • Paper is delivered to the tray until the bin 1 upper level sensor, Q11-332 is actuated. • The bin 1 elevator motor lowers the tray until the bin 1 upper level sensor, Q11-332 is deactuated. • As the tray is lowered to accommodate the increase in stack height, the bin 1 lower level sensor, Q11-333 is held actuated by the stack rear edge. • When the tray is emptied, the tray returns to the home position; the bin 1 lower level sensor, Q11-333 is de-actuated and the tray is elevated until both the bin 1 lower level sensor, Q11-333 and bin 1 upper level sensor, Q11-332 are made. The tray is then lowered until the bin 1 upper level sensor, Q11-332 is just cleared. In the home position the bin one upper limit switch, S11-334 is also actuated.