Description: Support Finger Position RAP 311-473-00-171 The support finger has failed to return to the initial position. 311-474-00-171 The support finger has failed to move from the initial position. 311-475-00-171 The support finger has failed to return to the home position. 311-476-00-171 The support finger has failed to move from the home position. 311-477-00-171 The support finger has failed to return to the out position. 311-478-00-171 The support finger has failed to move from the out position.
Remedy: NOTE: When manually extending the fingers to check the sensors, the home sensor operates first, followed by the init sensor. The away sensor operates when the fingers are fully extended. All three sensors are spared as part of the rear tamper assembly. shows the component locations. Enter dC330 code 011-192, support finger home sensor, Q11-192. Note the position of the support fingers at rest. Using a screwdriver, or with a finger, turn the gear wheel shown, downwards. The support fingers extend to the right as the gear is turned. When the support fingers have extended by about six millimeters, the support finger home sensor changes state. The display changes from High to Low. Y↓N→Go to Flag 1. Check Q11-192. Refer to: • GP 11 How to Check a Sensor. • P/J402, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Rear tamper assembly, PL 11.140 Item 13. • Ejector assembly, PL 11.140 Item 2. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code 011-191 and continue turning the gear wheel. When the support fingers have extended by about 25mm, the support finger init sensor changes state. The display changes from High to Low. Y↓N→Go to Flag 2. Check the support finger init sensor, Q11-191. Refer to: • GP 11 How to Check a Sensor. • P/J402, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Rear tamper assembly, PL 11.140 Item 13. • Ejector assembly, PL 11.140 Item 2. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code 011-193, support finger out sensor, Q11-193 and continue turning the gear wheel. When the support fingers have extended by about 105mm, the support finger out sensor changes state. The display changes from High to Low. Y↓N→Go to Flag 3. Check Q11-193. Refer to: • GP 11 How to Check a Sensor. • P/J402, HVF Control PWB • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Rear tamper assembly, PL 11.140 Item 13. • Ejector assembly, PL 11.140 Item 2. • HVF control PWB, PL 11.157 Item 2. Make several small sets of copies and observe that the support fingers are extended between each set. NOTE: If copies can not be made, go to the check of the support finger motor encoder. The support fingers are extended. Y↓N→Remove the HVF top cover and rear cover-171. Enter the dC330 code 011- 172, support finger motor encoder, Q11-172. Manually turn the support motor encoder disc. The encoder sensor changes state. Y↓N→Go to Flag 4. Check Q11-172. Refer to: • GP 11 How to Check a Sensor. • P/J402, HVF Control PWB. • 311A-171 HVF Power Distribution RAP. Install new components as necessary: • Support finger motor encoder sensor, PL 11.140 Item 15. • HVF control PWB, PL 11.157 Item 2. Go to Flag 5. Check the wiring between P/J802 and the support finger motor. Repair as necessary. Install new components as necessary: • Motor encoder assembly, PL 11.140 Item 18. • HVF control PWB, PL 11.157 Item 2. Perform SCP 5 Final Actions.