Code: 312D-150
Description: LVF BM Power Distribution RAP The LVF BM has an integral power supply providing +24V and +5V supplies to the LVF PWB and the LVF BM PWB. The AC power for the LVF BM power supply comes from the LVPS and base module of the machine.
Remedy: Close or cheat all the LVF BM interlocks. LED 2 on the LVF PWB is illuminated. Y↓N→+24V is available at Fuse (F1) on the LVF PWB. Y↓N→Go to Flag 2. Check for +24V between the pins that follow on P/J300: • Pin 1 and pin 2. • Pin 1 and pin 3. • Pin 1 and pin 6. • Pin 1 and pin 7. • Pin 5 and pin 2. • Pin 5 and pin 3. • Pin 5 and pin 6. • Pin 5 and pin 7. +24V is available between all the checked pins. Y↓N→Disconnect P/J300, check for +24V between the pins that follow on the end of the harness: • Pin 1 and pin 2. • Pin 1 and pin 3. • Pin 1 and pin 6. • Pin 1 and pin 7. • Pin 5 and pin 2. • Pin 5 and pin 3. • Pin 5 and pin 6. • Pin 5 and pin 7. +24V is available between all the checked pins on the end of the harness. Y N. Loosen the 4 screws and lift the power supply module away from the LVF BM frame. Go to Flag 1. ACL is available at CN1 between pins 1 and 3. Y↓N→Go to the 301C AC Power RAP and check the AC output voltages. Check the wiring and connectors between CN2 and P/J300. The wiring is good. Y↓N→Repair the wiring. Install a new power supply module, PL 12.425 Item 2. Check for a short or open circuit in the wiring or connectors between P/J300 on the LVF PWB and CN 2 on the power supply module. Refer to GP 7. +24 V is available at PJ315 pin 5 on the LVF PWB. Y↓N→Go to the 312-310-00-150, 312-312-00-150, 312-313-00-150 Interlocks RAP. WARNING Do not install a fuse of a different type or rating. Installing the wrong type or rating of fuse can cause overheating and a risk of fire. Perform the steps that follow: • Switch off the machine, GP 14. • Go to Flag 3, Flag 4, Flag 5 and Flag 6. Disconnect all the +24V harnesses to components. • Check each harness for short circuits and overheating, GP 7. • Repair or install new components as necessary. • Install a new fuse F1 on the LVF PWB. Switch on the machine, GP 14. • Monitor the voltage at the top end of the fuse and re-connect the circuits one at a time. Energize the re-connected components using the dC330 control codes shown. • If the voltage drops below +22V, switch off the machine, GP 14. Re-check the component and harness for overheating or short circuits. Repair or install new components as necessary. Install a new LVF PWB, PL 12.425 Item 8. +5V is available at P/J300 between pins 4 and 6, also between pins 7 and 8. Y↓N→Disconnect P/J300. +5V is available at P/J300 between pins 4 and 6, also between pins 7 and 8 on the end of the harness. Y↓N→Check the wiring between CN2 and P/J300. The wiring is good. Y↓N→Repair the wiring. Install a new power supply module, PL 12.425 Item 2. Perform the steps that follow 1. Switch off the machine, GP 14. 2. Go to Flag 3, Flag 4 and Flag 5.Disconnect all the +5V components. 3. Check each circuit for short circuits and overheating, GP 7. 4. Install new components as necessary. 5. Reconnect P/J300 and switch on the machine, GP 14. 6. Monitor the voltage at P/J300 pin 8, reconnect the circuits one at a time using the dC330 control codes shown. 7. If the voltage falls below +4.7V switch off the machine, GP 14. Re-check the last reconnected component and harness for overheating or short circuits. Install new components as necessary. Perform SCP 5 Final Actions.