Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 366A — Xerox WorkCentre 5945

Code: 366A

Description: Side 2 LED Exposure Lamp Failure RAP The side 2 LED exposure lamp failed to illuminate.
Remedy: Refer to. Open the SPDH, then the jam clearance guide. Enter the dC330 code 066- 002, DH exposure lamp. The LED lamp assembly in the side 2 scan assembly illuminates. Y↓N→Go to Flag 5. +24V is available at P/J453 between pin 1 and pin 3, and between pin 2 and pin 4. Y↓N→Go to Flag 1. +24V is available at P/J410 between pins 19 and 20, between pins 21 and 22, between pins 23 and 24, and between pins 25 and 26. Y↓N→+24V is available at P/J861 between pins 7 and 8, between pins 5 and 6, between pins 3 and 4, and between pins 1 and 2. Y↓N→Check the power supply. Refer to: • 301B 0V Distribution RAP. • 301G +24V Distribution RAP. Check the SBC PWB/scanner PWB comms/power harness, PL 60.20 Item 5. Check P/J861 on the SBC PWB and P/J410 on the Scanner PWB. Repair as necessary. Go to Flag 1, Flag 2 and Flag 3. Disconnect, check and clean if necessary, then reconnect P/J410, P/J418, P/J459, P/J458 and P/J452. +24V is now available at P/J453 between pin 1 and pin 3, and between pin 2 and pin 4. Y↓N→Install new components as necessary: • Side 2 scan assembly power ribbon cable, PL 5.10 Item 6. • Side 2 CCD PWB, PL 60.30 Item 4. • SPDH PWB, PL 5.10 Item 5. • Scanner PWB, PL 60.20 Item 4. Go to Flag 6. +24V is available at P/J454 between pin 1 and pin 3, and between pin 2 and pin 4. Y↓N→Check the wiring and connectors between P/J453 and P/J454. Repair as necessary. Go to Flag 7 and Flag 8. Check the wiring and connectors between P/J454 and P/ J455. The wiring and connectors are good. Y↓N→Repair the wiring or connectors as necessary. . Go to Flag 4. Check that both ends of the side 2 scan assembly data ribbon cable are clean and securely connected. The ribbon cable connections are good. Y↓N→Clean and reconnect the ribbon cable. If necessary, install a new side 2 scan assembly data ribbon cable, PL 5.10 Item 16. Install a new side 2 scan assembly data ribbon cable, PL 5.10 Item 16. Go to Flag 6. +24V is available at P/J454 between pin 1 and pin 3, and between pin 2 and pin 4. Y↓N→Check the wiring and connectors between P/J453 and P/J454. Repair as necessary. Go to Flag 7 and Flag 8. Check the wiring and connectors between P/J454 and P/J455. The wiring and connectors are good. Y↓N→Repair the wiring or connectors as necessary. . Go to Flag 4. Check that both ends of the side 2 scan assembly data ribbon cable are clean and securely connected. The ribbon cable connections are good. Y↓N→Clean and reconnect the ribbon cable. If necessary, install a side 2 scan assembly data ribbon cable PL 5.10 Item 16. Perform the steps that follow: 1. Install a new side 2 scan assembly data ribbon cable, PL 5.10 Item 16. 2. ADJ 60.3 IIT Registration, Magnification and Calibration. 3. SCP 5 Final Actions. Perform SCP 5 Final Actions.

← Xem tất cả mã lỗi Xerox WorkCentre 5945

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie