Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 381-194-00 — Xerox WorkCentre 5945

Code: 381-194-00

Description: Lead Edge Late to TAR 1 Sensor from Tray 2 RAP 381-194-00 The lead edge of the paper failed to actuate the tray 1 TAR sensor within the correct time after feeding paper from tray 2.
Remedy: NOTE: The front door and left door must be closed, or their respective interlock switches must be cheated when checking +24V components. Enter dC330 code 081-001, tray 1 TAR sensor, Q81-001. Open the left door. Manually actuate Q81-001. The display changes. Y↓N→Go to Flag 1. Check Q81-001. Refer to: • GP 11 How to Check a Sensor. • P/J750, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new Tray 1 TAR sensor, PL 80.10 Item 5. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 082-001, tray 2 TAR sensor, Q82-001. Manually actuate Q82-001. The display changes. Y↓N→Go to Flag 2. Check Q82-001. Refer to: • GP 11 How to Check a Sensor. • P/J750, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new Tray 2 TAR sensor, PL 80.10 Item 5. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 080-006, TAR/bypass tray motor, MOT80-006. The motor runs. Y↓N→Go to Flag 3. Check MOT80-006. Refer to: • GP 10 How to Check a Motor. • P/J754, IOT PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new TAR/bypass tray motor, PL 80.25 Item 5. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Observe the transport rolls, PL 80.25 Item 7. The transport rolls rotate. Y↓N→Check the transport roll drive belt, drive pulley and pulley, PL 80.25. Install new components as necessary: • Transport roll drive belt, PL 80.25 Item 2. • Pulley, PL 80.25 Item 4. • Transport roll bearing, PL 80.25 Item 6. • Transport roll, PL 80.25 Item 7. CAUTION To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT71- 010 is run in service mode. Enter dC330 code 081-020, tray 2 elevator/feed motor MOT072-010. Pull out the tray. The feed rolls rotate. Y↓N→Remove the tray 2 feed assembly from the machine. Manually rotate the feed roll shaft. The drive gears rotate. Y↓N→Check the drive gears for damage. If necessary install new components, PL 80.26. Install the tray 2 feed assembly. Go to Flag 4. Check MOT072-010. Refer to: • GP 10 How to Check a Motor. • P/J752, IOT PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new Tray 2 elevator/feed motor, PL 80.26 Item 6. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Observe the nudger roll, PL 80.26 Item 5. The nudger roll rotates. Y↓N→Check the nudger roll drive belt and drive coupling for damage. If necessary install new components, PL 80.26. Remove the paper tray. Manually activate the retard nip split mechanism. The retard roll moves against the feed roll. Y↓N→Check the retard roll drive coupling and mechanism for damage. If necessary install new components, PL 80.26. Perform the steps that follow: • Clean the feed roll using a cloth dampened with water. • Check the roll assembly, PL 80.26 Item 3. • Check the paper feed assembly, PL 80.26 Item 1.

← Xem tất cả mã lỗi Xerox WorkCentre 5945

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie