Code: 312-462-00-150
Description: Bin 1 Movement Failure RAP 312-462-00-150 Bin 1 failed to move. NOTE: The home position of bin 1 is when the bin is just lower than the bin 1 upper level sensor. See the final actions at the end of the procedure. TWO sensors and 2 switches monitor the level of paper in bin 1 and the position of the tray: • The bin 1 upper level sensor, detects the top of the paper stack in bin 1, or the empty bin 1. • The bin 1 90% full sensor detects when the tray has descended to a position where the tray is 90% full. • Bin 1 upper limit switch, S12-190. • Bin 1 lower limit switch, S12-191.
Remedy: NOTE: All LVF BM interlocks must be made to supply +24V to the motors. Remove the LVF BM rear cover. Enter dC330 code 012-163, bin 1 motor encoder sensor, Q12- 163. Slowly rotate the encoder disk by hand. The display changes. Y↓N→Go to Flag 2. Check Q12-163. Refer to: • GP 11 How to Check a Sensor. • P/J304, LVF PWB. • 312D-150 LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 motor encoder sensor, PL 12.340 Item 5. • LVF PWB, PL 12.425 Item 8. Enter dC330 code 012-242, bin 1 elevator motor cycle. Bin 1 cycles down and up. Y↓N→Go to Flag 1. Check bin 1 elevator motor MOT12-241. Refer to: • GP 10 How to Check a Motor. • P/J318, LVF PWB. • 312D-150 LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 elevator motor, PL 12.340 Item 7. • LVF PWB, PL 12.425 Item 8., enter dC330, code 012-188, bin 1 upper level sensor, Q12-188. Actuate Q12-188. The display changes. Y↓N→Go to Flag 3. Check Q12-188. Refer to: • GP 11 How to Check a Sensor. • P/J314, LVF PWB. • 312D-150 LVF BM Power Distribution RAP. •-150 LVF BM Un-docking. Repair or install new components as necessary: • Bin 1 upper level sensor, PL 12.345 Item 3. • LVF PWB, PL 12.425 Item 8.. Enter dC330 code 012-190, bin 1 upper limit switch, S12-190. Actuate S12- 190. The display changes. Y↓N→Go to Flag 4. Check S12-190. Refer to: • GP 13 How to Check a Switch. • P/J315, LVF PWB. • 312D-150 LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 upper limit switch, PL 12.340 Item 3. • LVF PWB, PL 12.425 Item 8. Enter dC330 code 012-191, bin 1 lower limit switch, S12-191. Actuate S12-190. The display changes. Y↓N→Go to Flag 5. Check S12-191. Refer to: • GP 13 How to Check a Switch. • P/J314, LVF PWB. • 312D-150 LVF BM Power Distribution RAP. •-110 LVF BM Un-docking. Repair or install new components as necessary: • Bin 1 lower limit switch, PL 12.345 Item 1. • LVF PWB, PL 12.425 Item 8. Enter dC330 code 012-187, bin 1 90% full sensor, Q12-187. Actuate Q12-187. The display changes. Y↓N→Go to Flag 6. Check Q12-187. Refer to: • GP 11 How to Check a Sensor. • P/J316, LVF PWB. • 312D-150, LVF BM Power Distribution RAP. Repair or install new components as necessary: • Bin 1 90% full sensor, PL 12.340 Item 5. • LVF PWB, PL 12.425 Item 8. As final actions, check the sequence of operation: 1. Paper is delivered to the tray until the bin 1 upper level sensor, Q12-188 is actuated. 2. The bin 1 elevator motor, MOT12-241 lowers the tray until the bin 1 upper level sensor, Q12-188 is de-actuated. 3. The bin 1 elevator motor, MOT12-241 raises the tray until the paper stack height actuates the bin 1 upper level sensor, then MOT12-241 lowers the tray to continue the cycle. 4. When the tray is emptied, the tray returns to the home position. The tray is elevated until the bin 1 upper level sensor, Q12-188 is made. The tray is then lowered until Q12-188 is just cleared. In the home position the bin 1 upper limit switch, S12-190 is actuated.