Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 312D-150 — Xerox WorkCentre 5955

Code: 312D-150

Description: LVF BM Power Distribution RAP The LVF BM has an integral power supply providing +24V and +5V supplies to the LVF PWB and the LVF BM PWB. The AC power for the LVF BM power supply comes from the LVPS and base module of the machine.
Remedy: Close or cheat all the LVF BM interlocks. LED 2 on the LVF PWB is illuminated. Y↓N→+24V is available at Fuse (F1) on the LVF PWB. Y↓N→Go to Flag 2. Check for +24V between the pins that follow on P/J300: • Pin 1 and pin 2. • Pin 1 and pin 3. • Pin 1 and pin 6. • Pin 1 and pin 7. • Pin 5 and pin 2. • Pin 5 and pin 3. • Pin 5 and pin 6. • Pin 5 and pin 7. +24V is available between all the checked pins. Y↓N→Disconnect P/J300, check for +24V between the pins that follow on the end of the harness: • Pin 1 and pin 2. • Pin 1 and pin 3. • Pin 1 and pin 6. • Pin 1 and pin 7. • Pin 5 and pin 2. • Pin 5 and pin 3. • Pin 5 and pin 6. • Pin 5 and pin 7. +24V is available between all the checked pins on the end of the harness. Y N. Loosen the 4 screws and lift the power supply module away from the LVF BM frame. Go to Flag 1. ACL is available at CN1 between pins 1 and 3. Y↓N→Go to the 301C AC Power RAP and check the AC output voltages. Check the wiring and connectors between CN2 and P/J300. The wiring is good. Y↓N→Repair the wiring. Install a new power supply module, PL 12.425 Item 2. Check for a short or open circuit in the wiring or connectors between P/J300 on the LVF PWB and CN 2 on the power supply module. Refer to GP 7. +24 V is available at PJ315 pin 5 on the LVF PWB. Y↓N→Go to the 312-310-00-150, 312-312-00-150, 312-313-00-150 Interlocks RAP. WARNING Do not install a fuse of a different type or rating. Installing the wrong type or rating of fuse can cause overheating and a risk of fire. Perform the steps that follow: • Switch off the machine, GP 14. • Go to Flag 3, Flag 4, Flag 5 and Flag 6. Disconnect all the +24V harnesses to components. • Check each harness for short circuits and overheating, GP 7. • Repair or install new components as necessary. • Install a new fuse F1 on the LVF PWB. Switch on the machine, GP 14. • Monitor the voltage at the top end of the fuse and re-connect the circuits one at a time. Energize the re-connected components using the dC330 control codes shown. • If the voltage drops below +22V, switch off the machine, GP 14. Re-check the component and harness for overheating or short circuits. Repair or install new components as necessary. Install a new LVF PWB, PL 12.425 Item 8. +5V is available at P/J300 between pins 4 and 6, also between pins 7 and 8. Y↓N→Disconnect P/J300. +5V is available at P/J300 between pins 4 and 6, also between pins 7 and 8 on the end of the harness. Y↓N→Check the wiring between CN2 and P/J300. The wiring is good. Y↓N→Repair the wiring. Install a new power supply module, PL 12.425 Item 2. Perform the steps that follow 1. Switch off the machine, GP 14. 2. Go to Flag 3, Flag 4 and Flag 5.Disconnect all the +5V components. 3. Check each circuit for short circuits and overheating, GP 7. 4. Install new components as necessary. 5. Reconnect P/J300 and switch on the machine, GP 14. 6. Monitor the voltage at P/J300 pin 8, reconnect the circuits one at a time using the dC330 control codes shown. 7. If the voltage falls below +4.7V switch off the machine, GP 14. Re-check the last reconnected component and harness for overheating or short circuits. Install new components as necessary. Perform SCP 5 Final Actions.

← Xem tất cả mã lỗi Xerox WorkCentre 5955

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie