Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 373-100-00, 373-217-00 — Xerox WorkCentre 5955

Code: 373-100-00, 373-217-00

Description: Tray 3 Elevator Lift Failure RAP 373-100-00 Tray 3 stack height sensor failed to actuate within the correct time after the elevator motor turned on. 373-217-00 Tray 3 failed to elevate during printing as sheets were fed from the tray. NOTE: Rapid closure of tray 4 when tray 3 is being elevated may cause this fault.
Remedy: Enter dC330 code 073-300, tray 3 home sensor, Q73-300. Pull out tray 3, then push tray 3 fully home. The display changes. Y↓N→Go to Flag 1. Check Q73-300. Refer to: • GP 11 How to Check a Sensor. • P/J755, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new tray 3 home sensor, PL 70.21 Item 4. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 073-330, tray 3 stack height sensor, Q73-330. Pull out tray 3. Manually actuate Q73-330. The display changes. Y↓N→Go to Flag 2. Check Q73-330. Refer to: • GP 11 How to Check a Sensor. • P/J755, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new tray 3 stack height sensor, PL 80.32 Item 6. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. (W/O TAG 003 Only). Disconnect P/J756 on the IOT PWB. Connect a service meter between pin 1 and pin 2 on the wiring side of the connector. Continuity is measured when the stack limit switch is deactuated and an open circuit is measured when the switch is actuated. Y↓N→Go to Flag 3. Check the tray 3 over elevate switch. Refer to: • GP 13 How to Check a Switch. • P/J756, IOT PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new tray 3 over elevate switch, PL 80.32 Item 7. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-030 is run in service mode. Re-connect P/J756. Enter dC330 code 073-010, tray 3 elevator motor, MOT73-010. Pull out tray 3. The motor runs. Y↓N→Go to Flag 4. Check MOT73-010. Refer to: • GP 10 How to Check a Motor. • P/J756, IOT PWB. •. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP Install new components as necessary: • Tray 3 elevator motor, PL 70.21 Item 1. • IOT PWB, PL 1.10 Item 2. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Check the components that follow: • The elevator cables, PL 70.18 Item 3, PL 70.18 Item 4 and PL 70.18 Item 5. • The elevator drives gear coupling, PL 70.18 Item 16. If the fault persists, perform the 373B Tray 3 Out of Paper RAP.

← Xem tất cả mã lỗi Xerox WorkCentre 5955

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie