Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 374-100-00, 374-217-00 — Xerox WorkCentre 5955

Code: 374-100-00, 374-217-00

Description: Tray 4 Elevator Lift Failure RAP 374-100-00 Tray 4 stack height sensor failed to actuate within the correct time after the elevator motor turned on. 374-217-00 Tray 4 failed to elevate during printing as sheets were fed from the tray. NOTE: Rapid closure of tray 3 when tray 4 is being elevated may cause this fault.
Remedy: Enter dC330 code 074-300, tray 4 home sensor, Q74-300. Pull out tray 4, then push tray 4 fully home. The display changes. Y↓N→Go to Flag 1. Check Q74-300. Refer to: • GP 11 How to Check a Sensor. • GP 30 Tray 4 Control PWB Test Points. • P/J157, Tray 4 control PWB. • P/J775, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 home sensor, PL 70.21 Item 4. • Tray 4 control PWB, PL 70.21 Item 2. Enter dC330 code 074-330, tray 4 stack height sensor, Q74-330. Pull out tray 4. Manually actuate Q74-330. The display changes. Y↓N→Go to Flag 2. Check Q74-330. Refer to: • GP 11 How to Check a Sensor. • GP 30 Tray 4 Control PWB Test Points. • P/J157, Tray 4 control PWB. • P/J775, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 stack height sensor, PL 80.33 Item 7. • Tray 4 control PWB, PL 70.21 Item 2. (W/O TAG 004 Only). Disconnect P/J159 on the Tray 4 control PWB. Connect a service meter between pin 1 and pin 2 on the wiring side of the connector. Continuity is measured when the stack limit switch is deactuated and open circuit is measured when the switch is actuated. Y↓N→Go to Flag 3. Check the tray 4 over elevate switch. Refer to: • GP 13 How to Check a Switch. • GP 30 Tray 4 Control PWB Test Points. • P/J159, Tray 4 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 over elevate switch, PL 80.33 Item 8. • Tray 4 control PWB, PL 70.21 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the appropriate paper tray must be pulled out before MOT74-010 or MOT73-010 is run in service mode. Pull out tray 4. Enter dC330 code 074-010, tray 4 elevator motor, MOT74-010. The motor runs. Y↓N→Pull out tray 3. Enter dC330 code 073-010, tray 3 elevator motor, MOT73-010. The motor runs. Y↓N→Perform the 373-100-00, 373-217-00 Tray 3 Elevator Lift Failure RAP. Perform the steps that follow: • Remove the tray 4 elevator motor. • Remove the tray 3 elevator motor, PL 70.21 Item 1. • Install the tray 3 elevator motor in place of the tray 4 elevator motor. Enter dC330 code 074-010, MOT74-010. The motor runs. Y↓N→Go to Flag 4. Check the wiring between the LVPS and tray 4 control PWB. Refer to: • GP 30 Tray 4 Control PWB Test Points. • P/J158, Tray 4 control PWB. • P/J656, LVPS. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. The wiring is good. Y↓N→Repair the wiring. +24V is present at P/J158 pin 1. Y↓N→If necessary, install a new tray 4 control PWB, PL 70.21 Item 2. If the fault persists, perform the 301L LVPS RAP. Go to Flag 5. Check the wiring between the IOT PWB and tray 4 control PWB. Refer to: • GP 30 Tray 4 Control PWB Test Points. • P/J775, IOT PWB. • P/J155, Tray 4 control PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. The wiring is good. Y↓N→Repair the wiring. +5V is present at P/J155 pin 11. Y↓N→Perform OF7 IOT PWB Diagnostics RAP. Install a new tray 4 control PWB, PL 70.21 Item 2. Install a new tray 4 elevator motor, PL 70.21 Item 1. Check the components that follow: • The elevator cables, PL 70.19 Item 3, PL 70.19 Item 4 and PL 70.19 Item 5. • The elevator drives gear coupling, PL 70.19 Item 16. If the fault persists, perform the 374B Tray 4 Out of Paper RAP.

← Xem tất cả mã lỗi Xerox WorkCentre 5955

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie