Code: 381-136-00
Description: Lead Edge Late to Tray 3 Feed Sensor RAP 381-136-00 The lead edge of the paper failed to actuate the tray 3 feed sensor within the correct time after feeding paper from tray 3.
Remedy: NOTE: The front door and left door must be closed, or their respective interlock switches must be cheated when checking +24V components. Enter dC330 code 081-103, tray 3 feed sensor, Q81-103. Manually actuate Q81- 103. The display changes. Y↓N→Go to Flag 1. Check Q81-103. Refer to: • GP 11 How to Check a Sensor. • P/J755, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new tray 3 feed sensor, PL 80.32 Item 3. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 081-045, HCF transport motor, MOT81-045. The motor runs. Y↓N→Go to Flag 2. Check MOT81-045. Refer to: • GP 10 How to Check a Motor. • P/J756, IOT PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new HCF transport motor, PL 80.36 Item 13. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Observe the HCF transport roll, PL 80.33 Item 4. The HCF transport roll rotates. Y↓N→Check the components that follow: • HCF transport roll, PL 80.33 Item 4. • Gear, PL 80.33 Item 2. • Transport gear pulley, PL 80.36 Item 12. Install new components as necessary. CAUTION To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT81- 030 is run in service mode. Enter dC330 code 081-030, tray 3 feed motor, MOT81-030. Pull out tray 3. The motor runs. Y↓N→Go to Flag 3. Check MOT81-030. Refer to: • GP 10 How to Check a motor. • P/J755, IOT PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new Tray 3 feed motor, PL 80.32 Item 8. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Enter dC330 code 081-030, tray 3 feed motor, MOT81-030. Add the code 081-033, tray 3 feed clutch, CL81-033. Pull out tray 3. Observe the tray 3 feed and nudger rolls. NOTE: The bypass tray clutch will also energize when component control code 081-033 is entered. The rolls rotate. Y↓N→Go to Flag 4. Check CL81-033. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J755, IOT PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. If necessary, install a new tray 3 paper feed assembly, PL 80.32 Item 1. If the fault persists, perform the OF7 IOT PWB Diagnostics RAP. Perform the steps that follow: • Clean the feed roll, nudger roll and retard roll using a cloth dampened with water. • Check the feed roll, retard roll and nudger roll for wear. If necessary install a new feed/ nudger/retard roll spares kit, PL 31.12 Item 15. • Perform the adjustments that follow: – ADJ 80.3 Tray 3 and Tray 4 Retard Roll Pressure. – ADJ 80.1 Tray 3 and Tray 4 Nudger Roll Pressure. • Check the tray 3 stack height sensor actuator on the feed assembly, PL 80.32 Item 6. • Check the tray is level. 1. Pull out tray 3 and remove all of the paper from the tray. 2. Remove the tray 3 front cover. 3. Manually elevate the tray to the top of its travel by rotating the elevator cable drum at the front of the tray. 4. At the 3 locations where the metal paper tray protrudes through the plastic outer frame of tray 3, check that the top surface of the metal paper tray is the same distance from the inside top of the slots. 5. If the tray is not level, install new elevator cables, PL 70.18 Item 7. • Check the tray 3 paper tray guide for paper cut damage. If necessary install new components, PL 70.18 Item 14.