Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 381-167-00 — Xerox WorkCentre 5955

Code: 381-167-00

Description: Lead Edge Late to Tray 4 Exit Sensor RAP 381-167-00 The lead edge of the paper was late to the tray 4 exit sensor.
Remedy: NOTE: The front door and left door must be closed, or their respective interlock switches must be cheated when checking +24V components. Enter dC330 code 081-150, tray 4 exit sensor, Q81-150. Manually actuate Q81-150. The display changes. Y↓N→Go to Flag 1. Check Q81-150. Refer to: • GP 11 How to Check a Sensor. • GP 30 Tray 4 Control PWB Test Points. • P/J161, Tray 4 control PWB. • P/J775, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 exit sensor, PL 80.33 Item 6. Enter dC330 code 081-150, tray 4 exit sensor, Q81-150. Manually actuate Q81-150. The display changes. Y↓N→Go to Flag 2. Check the wiring between the Tray 4 control PWB and IOT PWB. Refer to: • GP 30 Tray 4 Control PWB Test Points. • P/J155, Tray 4 control PWB. • P/J775, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. The wiring is good. Y↓N→Repair the wiring. +5V is present at P/J155 pin 2. Y↓N→Perform OF7 IOT PWB Diagnostics RAP. Install a new tray 4 control PWB, PL 70.21 Item 2. CAUTION To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT81- 040 is run in service mode. Enter dC330 code 081-040, tray 4 feed motor, MOT81-040. The motor runs. Y↓N→Go to Flag 6. Check MOT81-040. Refer to: • GP 10 How to Check a Motor. • GP 30 Tray 4 Control PWB Test Points. • P/J162, Tray 4 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 feed motor, PL 80.33 Item 10. Enter dC330 code 081-040, tray 4 feed motor, MOT81-040. The motor runs. Y↓N→Go to Flag 3. Check the wiring between the Tray 4 control PWB and IOT PWB. Refer to: • GP 30 Tray 4 Control PWB Test Points. • P/J155, Tray 4 control PWB. • P/J775, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. The wiring is good. Y↓N→Repair the wiring. +5V is present at P/J155 pin 10. Y↓N→Perform OF7 IOT PWB Diagnostics RAP. Install a new tray 4 control PWB, PL 70.21 Item 2. The motor runs. Y↓N→Go to Flag 5. Check the wiring between the LVPS and Tray 4 control PWB. Refer to: • GP 30 Tray 4 Control PWB Test Points. • P/J158, Tray 4 control PWB. • P/J656, LVPS • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. The wiring is good. Y↓N→Repair the wiring. +24V is present at P/J158 pin 2. Y↓N→Perform the 301L LVPS RAP. Install a new tray 4 control PWB, PL 70.21 Item 2. Locate the tray 4 feed clutch, CL81-043. Enter dC330 code 081-040, tray 4 feed motor, MOT81-040. Add the code 081-043, tray 4 feed clutch, CL81-043. Pull out tray 4. Observe the tray 4 feed and nudger rolls. The rolls rotate. Y↓N→Go to Flag 4. Check CL81-043. Refer to: • GP 12 How to Check a Solenoid or Clutch. • GP 30 Tray 4 Control PWB Test Points. • P/J162, Tray 4 control PWB. • 301G +24V Distribution RAP. • 301B 0V Distribution RAP. Install new components as necessary: • Tray 4 paper feed assembly, PL 80.33 Item 1. Go to Flag 3. Check the wiring between the Tray 4 control PWB and IOT PWB. Refer to: • GP 30 Tray 4 Control PWB Test Points. • P/J155, Tray 4 control PWB. • P/J775, IOT PWB. • 301E +5V and +5VSB Distribution RAP. • 301B 0V Distribution RAP. The wiring is good. Y↓N→Repair the wiring. +5V is present at P/J155 pin 10. Y↓N→Perform OF7 IOT PWB Diagnostics RAP. Install a new tray 4 control PWB, PL 70.21 Item 2. Perform the steps that follow: • Clean the feed roll, nudger roll and retard roll using a cloth dampened with water. • Check the feed roll, nudger roll and retard roll for wear. If necessary install a new feed/ nudger/retard roll spares kit, PL 31.12 Item 15. • Perform the adjustments that follow: – ADJ 80.3 Tray 3 and Tray 4 Retard Roll Pressure. – ADJ 80.1 Tray 3 and Tray 4 Nudger Roll Pressure. • Check the tray 4 stack height sensor actuator on the feed assembly, PL 80.33 Item 7. • Check the tray is level: 1. Pull out tray 4. Remove all the paper from the tray. 2. Remove the tray 4 front cover. 3. Manually elevate the tray to the top of its travel by rotating the elevator cable drum at the front of the tray. 4. At the 3 locations where the metal paper tray protrudes through the outer plastic frame of tray 4, check that the top surface of the metal paper tray is the same distance from the inside top of the slots 5. If the tray is not level, install new elevator cables, PL 70.19 Item 7. • Check the tray 4 paper tray guide for paper cut damage, PL 70.19 Item 17. • If the fault persists, refer to GP 7. Check the components that follow: – The takeaway roll assembly, PL 80.36 Item 2. – The idler roll assembly, PL 80.36 Item 8. – HCF transport roll, PL 80.33 Item 4. – The idler roll assembly, PL 80.32 Item 2. Install new components as necessary.

← Xem tất cả mã lỗi Xerox WorkCentre 5955

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie