Code: 391A
Description: HVPS RAP To assist in identifying any suspected problems with the HVPS and the high voltage distribution.
Remedy: If fault code 341-302-00 is shown in fault history, remove the print cartridge, refer to the 301A Ground Distribution RAP and check for pitting on the print cartridge drive shaft in the area shown. If pitting is found on the shaft, follow the cleaning instructions in the 301A Ground Distribution RAP. If necessary install a new print cartridge, PL 90.17 Item 9. Go to Flag 1. +24V is available at P/J769 between pins 13 and 14. Y↓N→Disconnect P/J769. +24V is available at J769 on the IOT PWB. Y↓N→Perform the 301G +24V Distribution RAP and the 301B 0V Distribution RAP. Go to Flag 1. Check the wiring and connectors P/J769 and P/J830 between the IOT PWB and the HVPS. The wiring and connectors are good. Y↓N→Repair the wiring or install new components as necessary. Install a new HVPS, PL 1.10 Item 3. +24V is available at P/J830 between pins 12 and 13. Y↓N→Go to Flag 1. Check the wiring and connectors P/J769 and P/J830 between the IOT PWB and the HVPS. The wiring and connectors are good. Y↓N→Repair the wiring or install new components as necessary. Install a new HVPS, PL 1.10 Item 3. Ensure the machine is in standby mode. +2.4V to +2.6V is available between pins 9 and 10 on P/J830. Y↓N→Install a new HVPS, PL 1.10 Item 3. Check the high voltage circuits: NOTE: For information regarding the cleaning of xerographic components, refer to ADJ 90.1 Xerographics Cleaning. • BCR. Refer to PL 90.10. Check the items that follow: – Track (BCR) on the HVPS tray assembly for continuity, short circuits and damage. Ensure the contact area at each end is clean and undamaged. – The BCR contact on the HVPS is clean and undamaged. – The bias charge roll contact on the print cartridge is clean and undamaged. If necessary repair the high voltage track or install new components: – HVPS tray assembly, PL 90.10 Item 1. – HVPS, PL 1.10 Item 3. – Print cartridge, PL 90.17 Item 9. • DEV. Refer to PL 90.10. Check the items that follow: – Track (DEV) on the HVPS tray assembly for continuity, short circuits and damage. Ensure the contact area at each end is clean and undamaged. – The DB contact on the HVPS is clean and undamaged. – The developer bias contact on the print cartridge is clean and undamaged. If necessary repair the high voltage track or install new components: – HVPS tray assembly, PL 90.10 Item 1. – HVPS, PL 1.10 Item 3. – Print cartridge, PL 90.17 Item 9. • BTR. Refer to PL 90.10. Check the items that follow: – Track (BTR) on the HVPS tray assembly for continuity, short circuits and damage. Ensure the contact area at each end is clean and undamaged. – The BTR contact on the HVPS is clean and undamaged. – The bias transfer contact on the registration transfer housing is clean and undamaged. – The condition of the bias transfer roll and bearings. If necessary repair the high voltage track or install new components: – HVPS tray assembly, PL 90.10 Item 1. – HVPS, PL 1.10 Item 3. – Registration transfer housing, PL 80.15 Item 2. – Bias transfer roll, PL 80.15 Item 3. – Bias transfer roll bearings, PL 80.15 Item 9. • DTS. Refer to PL 90.10. Check the items that follow: – Track (DTS) on the HVPS tray assembly for continuity, short circuits and damage. Ensure the contact area at each end is clean and undamaged. – The DTS contact on the HVPS is clean and undamaged. – The detack saw contact on the registration transfer housing is clean and undamaged. If necessary repair the high voltage track or install new components: – HVPS tray assembly, PL 90.10 Item 1. – HVPS, PL 1.10 Item 3. – Registration transfer housing, PL 80.15 Item 2. If no fault was found, the HVPS is working correctly, return to the procedure that directed you here.