Code: 077-106
Description: Jam at Exit The paper does not reach the Registration Sensor within the specified time.
Causes: • Registration Sensor, PL2.3.5 • Registration Clutch, PL2.3.7 • Harness Assembly RKN SNS, PL2.2.25/26 • Main Drive Assembly, PL6.1.2 • Harness Assembly Main MOT, PL6.1.7 • MCU Board, PL7.2.2
Remedy: 1. Check the installation and operation of the Registration Roller and the Registration Pinch Roller Assembly. Are the Registration Roller and the Registration Pinch Roller Assembly installed properly? Go to step 2. Reinstall/replace the relevant part, then go to step 2. 2. Check connectors P/J12 and P/J120 between the MCU Board and the Registration Sensor. Are the connectors secure? Go to step 4. Reconnect the connectors, then go to step 3. 3. Does the error still occur when printing? Go to step 4. Complete. 4. Enter diagnostic mode and run the Regi Sensor test (see. You can also use the CE Diag Tool to run this test (see. Lift the Paper Tray Chute (PL3.3.3), does the number on the display increase by 1 each time the Paper Tray Chute is lifted? 1. SaveNVM to ESS 2. Replace the MCU Board. 3. LoadNVM from ESS Go to step 5. 5. Disconnect the MCU Board P/J12 and the Registration Sensor P/J120. Check the Harness Assembly RKN SNS for continuity. Is the harness damaged? Go to step 6. Repair the harness. 6. Check that the voltage across ground on the MCU Board P/J12-1 is +3.3 VDC. Is the voltage correct? Replace the Registration Sensor (Phaser 6020 and WorkCentre 6025 MFP, Phaser 6022 and WorkCentre 6027 MFP. Go to step 7. 1. SaveNVM to ESS 2. Replace the MCU Board 3. LoadNVM from ESS Go to step 7. 7. Does the error persist when printing? Go to step 8. Complete. 8. Check connectors P/J16 and P/J160 between the MCU Board and the Main Drive Assembly. Are the connectors secure? Go to step 9. Reconnect the connectors, then go to step 9. 9. Does the error persist when printing? Go to step 10. Complete. 10. Enter diagnostic mode and run the Main Motor test (see). You can also use the CE Diag Tool to run this test (see “Main Motor” on. Does the Main Drive Assembly function normally? Go to step 15. Go to step 11. 11. Check the Main Drive Assembly for proper installation. Is the Main Drive Assembly installed correctly? Go to step 12. Reseat the Main Drive Assembly, then go to step 12. 12. Does the error still occur when printing? Go to step 13. Complete. 13. Disconnect P/J16 from the MCU Board and P/J160 from the Main Drive Assembly. Check the continuity of the cable. Is the cable damaged? Repair the cable. Go to step 14. 14. Check the MCU Board P/J25 for proper connection. Is P/J25 securely connected? Go to step 15. Reconnect the connector, then go to step 15. 15. Does the error persist when printing? Go to step 16. Complete. 16. Check the power to the Main Drive Assembly. Disconnect P/J16 on the MCU Board. Are the voltages across ground at P/J16-2 and P/J16-4 approximately +24 VDC when the Interlock Switch is engaged? Replace the Main Drive Assembly, and then go to step 17. 1. SaveNVM to ESS 2. Replace the MCU Board. 3. LoadNVM from ESS Go to step 17. 17. Does the error persist when printing? Go to step 18. Complete. 18. Enter diagnostic mode and run the Regi Clutch test. You can also use the CE Diag Tool to run this test (see “Registration Clutch” on. Does the Registration Clutch function correctly? 1. SaveNVM to ESS 2. Replace the MCU Board. 3. LoadNVM from ESS Replace the Registration Clutch.