Code: 381
Description: Paper running jam (error code 381)
Remedy: Jam occurs immediately after the power is turned on.
(6-1-1) Check condition of the running path. Paper running path of the front unit Check if paper is jammed or not in the paper running path. Remove the jammed paper. (6-1-2) Check condition of the mechanical parts Check the sensor lever of the WR sensor. Check if shape and movement of the sensor levers have any abnormality or not. Replace the sensor lever with the good sensor lever. (6-1-3) Check condition of electrical parts Check the detection condition of the sensor signal. Confirm that the sensor signals are normally detected by using the SWITCH SCAN function of the maintenance menu. Replace the CU/PU board, or appropriate sensor(s) or connection cord(s). Check the sensor lever of the WR sensor. Check the following signal by using the CU/ PU board RGSNS connector 1: RGSNS 2pin: WR sensor Confirm that the above signal levels change when the sensor lever is operated. Replace the sensor.
Jam occurs immediately after a paper is taken into printer.
(6-2-1) Check condition of the paper running path Paper running path on the belt. Remove the ID unit and check if paper is jammed or not in the paper running path. Remove the jammed paper. (6-2-2) Check condition of the mechanical parts Check the sensor lever of the WR sensor. Check if shape and movement of the sensor levers have any abnormality or not. Replace the sensor lever with the good sensor lever. (6-2-3) Motor operation check Paper feed motor driver, belt motor driver and ID motor Confirm that the paper feed motor, belt motor and ID motor work normally by using the Motor & Clutch Test of the selfdiagnostic mode. Check if any load exists or not. Replace the CU/ PU board or the feed motor or the belt motor or the ID motor or the ID unit or the belt unit. Paper feed motor driver, belt motor driver Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Several M Between 2pin – FG: Several M Between 3pin – FG: Several M Between 4pin – FG: Several M Pull out the CU/PU board BELT connector, and check the following at the side of the connector: Between 1pin – FG: Several M Between 2pin – FG: Several M Between 3pin – FG: Several M Between 4pin – FG: Several M Replace the CU/PU board.
(6-1-1) Check condition of the running path. Paper running path of the front unit Check if paper is jammed or not in the paper running path. Remove the jammed paper. (6-1-2) Check condition of the mechanical parts Check the sensor lever of the WR sensor. Check if shape and movement of the sensor levers have any abnormality or not. Replace the sensor lever with the good sensor lever. (6-1-3) Check condition of electrical parts Check the detection condition of the sensor signal. Confirm that the sensor signals are normally detected by using the SWITCH SCAN function of the maintenance menu. Replace the CU/PU board, or appropriate sensor(s) or connection cord(s). Check the sensor lever of the WR sensor. Check the following signal by using the CU/ PU board RGSNS connector 1: RGSNS 2pin: WR sensor Confirm that the above signal levels change when the sensor lever is operated. Replace the sensor.
Jam occurs immediately after a paper is taken into printer.
(6-2-1) Check condition of the paper running path Paper running path on the belt. Remove the ID unit and check if paper is jammed or not in the paper running path. Remove the jammed paper. (6-2-2) Check condition of the mechanical parts Check the sensor lever of the WR sensor. Check if shape and movement of the sensor levers have any abnormality or not. Replace the sensor lever with the good sensor lever. (6-2-3) Motor operation check Paper feed motor driver, belt motor driver and ID motor Confirm that the paper feed motor, belt motor and ID motor work normally by using the Motor & Clutch Test of the selfdiagnostic mode. Check if any load exists or not. Replace the CU/ PU board or the feed motor or the belt motor or the ID motor or the ID unit or the belt unit. Paper feed motor driver, belt motor driver Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Several M Between 2pin – FG: Several M Between 3pin – FG: Several M Between 4pin – FG: Several M Pull out the CU/PU board BELT connector, and check the following at the side of the connector: Between 1pin – FG: Several M Between 2pin – FG: Several M Between 3pin – FG: Several M Between 4pin – FG: Several M Replace the CU/PU board.