Code: 380
Description: Feed jam (error code 380)
Remedy: (4-1) Jam occurs immediately after the power is turned on.
(4-1-1) Check condition of the paper running path Paper running path of the front unit Open the front cover check if paper is not jammed in the paper running path. Remove the jammed paper. (4-1-2) Check condition of the mechanical parts Hopping sensor, IN sensor and WR sensor lever check Check the sensor lever shapes and operations for any problem. Replace the sensor lever(s) with proper one(s). (4-1-3) Check condition of electrical parts Check the detection condition of the sensor signal. Confirm that the sensor signals are normally detected by using the Maintenance Menu SWITCH SCAN function. Replace the CU/PU board or sensor or cable. Hopping sensor, IN sensor and WR sensor output level check Check the following signals by using the CU/ PU board HPSNS and RGSNS connector: HPSNS 2pin: Hopping sensor RGSNS 5pin: IN sensor RGSNS 2pin: WR sensor Confirm that the above signal levels change when the sensor lever is operated. Replace the appropriate sensor(s).
(4-2) Jam occurs immediately after the paper feed is started.
(4-2-1) Check condition of the paper running path Paper running path of the front unit Check if paper is jammed or not in the paper running path. Remove the jammed paper. (4-2-2) Check condition of the mechanical parts Hopping sensor, IN sensor and WR sensor lever check Check the sensor lever shapes and operations for any problem Replace the sensor lever(s) with proper one(s). (4-2-3) Motor operation check Paper feed motor Confirm that the paper feed motor works normally by using the Motor & Clutch Test of the self-diagnostic mode. Replace the CU/ PU board or the feed motor. Paper feed motor driver Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Several M Between 2pin – FG: Several M Between 3pin – FG: Several M Between 4pin – FG: Several M Replace the CU/PU board. (4-2-4) Clutch operation check Feed clutch and regist clutch Confirm that the feed clutch and regist clutch works normally by using the Motor & Clutch Test of the self-diagnostic mode. Pull out the cassette for the rollers to be seen, and check operation. Replace the CU/ PU board or the feed clutch or regist clutch. Paper feed motor drive cable Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not. Check also that cables are assembled without any abnormality. Replace the cable with the good cable that normalizes the connection condition. Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Do not short-circuit Between 2pin – FG: Do not short-circuit Between 3pin – FG: Do not short-circuit Between 4pin – FG: Do not short-circuit Replace the cable and properly assemble. Feed clutch cable Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not. Normalizes the connection condition. Replace the clutch. Feed clutch Pull out the CU/PU board HOC connector, and check the following at the side of the connector. Between 1pin – FG: Do not short-circuit Between 1pin – 2pin: About 240 Replace the clutch and properly assemble appropriate parts. Regist clutch Pull out the CU/PU board REC connector, and check the following at the side of the connector. Between 1pin – FG: Do not short-circuit Between 1pin – 2pin: About 240 Replace the clutch and properly assemble appropriate parts. Paper feed motor Pull out the CU/PU board HOP connector, and check the following at the side of the connector. Between 1pin – 2pin: 3.4 or 5 Between 3pin – 4pin: 3.4 or 5 Replace the Paper feed motor.
(4-1-1) Check condition of the paper running path Paper running path of the front unit Open the front cover check if paper is not jammed in the paper running path. Remove the jammed paper. (4-1-2) Check condition of the mechanical parts Hopping sensor, IN sensor and WR sensor lever check Check the sensor lever shapes and operations for any problem. Replace the sensor lever(s) with proper one(s). (4-1-3) Check condition of electrical parts Check the detection condition of the sensor signal. Confirm that the sensor signals are normally detected by using the Maintenance Menu SWITCH SCAN function. Replace the CU/PU board or sensor or cable. Hopping sensor, IN sensor and WR sensor output level check Check the following signals by using the CU/ PU board HPSNS and RGSNS connector: HPSNS 2pin: Hopping sensor RGSNS 5pin: IN sensor RGSNS 2pin: WR sensor Confirm that the above signal levels change when the sensor lever is operated. Replace the appropriate sensor(s).
(4-2) Jam occurs immediately after the paper feed is started.
(4-2-1) Check condition of the paper running path Paper running path of the front unit Check if paper is jammed or not in the paper running path. Remove the jammed paper. (4-2-2) Check condition of the mechanical parts Hopping sensor, IN sensor and WR sensor lever check Check the sensor lever shapes and operations for any problem Replace the sensor lever(s) with proper one(s). (4-2-3) Motor operation check Paper feed motor Confirm that the paper feed motor works normally by using the Motor & Clutch Test of the self-diagnostic mode. Replace the CU/ PU board or the feed motor. Paper feed motor driver Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Several M Between 2pin – FG: Several M Between 3pin – FG: Several M Between 4pin – FG: Several M Replace the CU/PU board. (4-2-4) Clutch operation check Feed clutch and regist clutch Confirm that the feed clutch and regist clutch works normally by using the Motor & Clutch Test of the self-diagnostic mode. Pull out the cassette for the rollers to be seen, and check operation. Replace the CU/ PU board or the feed clutch or regist clutch. Paper feed motor drive cable Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not. Check also that cables are assembled without any abnormality. Replace the cable with the good cable that normalizes the connection condition. Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Do not short-circuit Between 2pin – FG: Do not short-circuit Between 3pin – FG: Do not short-circuit Between 4pin – FG: Do not short-circuit Replace the cable and properly assemble. Feed clutch cable Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not. Normalizes the connection condition. Replace the clutch. Feed clutch Pull out the CU/PU board HOC connector, and check the following at the side of the connector. Between 1pin – FG: Do not short-circuit Between 1pin – 2pin: About 240 Replace the clutch and properly assemble appropriate parts. Regist clutch Pull out the CU/PU board REC connector, and check the following at the side of the connector. Between 1pin – FG: Do not short-circuit Between 1pin – 2pin: About 240 Replace the clutch and properly assemble appropriate parts. Paper feed motor Pull out the CU/PU board HOP connector, and check the following at the side of the connector. Between 1pin – 2pin: 3.4 or 5 Between 3pin – 4pin: 3.4 or 5 Replace the Paper feed motor.