Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 390 — OKI MC573dn

Code: 390

Description: (5) Paper feed jam (error code 390: Multipurpose tray)
Remedy: (5-1) Jam occurs immediately after the power is turned on. (Multipurpose tray)
(5-1-1) Check condition of the paper running path Paper running path of the front unit Check if paper is jammed or not in the paper running path. Remove the jammed paper. (5-1-2) Check condition of the mechanical parts IN sensor and WR sensor lever check Check the sensor lever shapes and operations for any problem Replace the sensor lever(s) with proper one(s) (5-1-3) Check condition of electrical parts Check the detection condition of the sensor signal. Confirm that the sensor signals are normally detected by using the SWITCH SCAN function of the Maintenance menu. Replace the CU/PU board, or appropriate sensor(s) or connection cord(s). In sensor and WR sensor output level check Check the following signals by using the CU/PU board RGSNS connector : RGSNS 5pin: IN sensor RGSNS 2pin: WR sensor Confirm that the above signal levels change when the sensor lever is operated. Replace the sensor.
(5-2) Jam occurs immediately after paper feed is started. (Multipurpose tray)
(5-2-1) Check condition of the paper running path Paper running path of the multipurpose tray Check if paper is jammed or not in the paper running path. Remove the jammed paper. Sheet Receive of the multipurpose tray Confirm that the Sheet Receive has moved up normally. Confirm that the support spindle and spring of the Sheet Receive have been installed in the specified positions normally. Correct installation of the above parts so that the Sheet Receive moves up to the specified position normally. (5-2-2) Check condition of the mechanical parts IN sensor and WR sensor lever check Check the sensor lever shapes and operations for any problem Replace the sensor lever(s) with proper one(s). Front cover Confirm that the locks in the right and left of the front cover are locked normally. Replace the font cover assembly Check the feed roller and the pickup roller. Check if any foreign materials such as paper dust on the surface of the feed roller or of the pickup roller or not. Remove the foreign material. Check if the feed roller has worn out or not. Replace the feed roller. (5-2-3) Motor operation check Paper feed motor Confirm that the paper feed motor works normally by using the Motor & Clutch Test of the self-diagnostic mode. Replace the CU/ PU board or the feed motor. Paper feed motor driver Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Several M Between 2pin – FG: Several M Between 3pin – FG: Several M Between 4pin – FG: Several M Replace the CU/PU board. (5-2-4) Clutch operation check MPT clutch and regist clutch Confirm that the paper feed motor works normally by using the Motor & Clutch Test of the self-diagnostic mode. Pull out the cassette for the rollers to be seen, and check operation. Replace the CU/PU board or MPT clutch or regist clutch. (5-2-5) Check the system connection Paper feed motor drive cable Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not. Check also that cables are assembled without any abnormality. Replace the cable with the good cable that normalizes the connection condition. Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Do not short-circuit Between 2pin – FG: Do not short-circuit Between 3pin – FG: Do not short-circuit Between 4pin – FG: Do not short-circuit Replace the cable with the good cable that normalizes the connection condition. MPT clutch cable Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not. Check also that cables are assembled without any abnormality. Normalizes the connection condition. Replace the clutch. MPT clutch Pull out the CU/PU board MPC connector, and check the following at the side of the connector. Between 1pin – FG: Do not short-circuit Between 1pin – 2pin: About 240 Replace the clutch and properly assemble appropriate parts. Paper feed motor Pull out the CU/PU board HOP connector, and check the following at the side of the connector. Between 1pin – 2pin: 3.4 or 5 Between 3pin – 4pin: 3.4 or 5 Replace the Paper feed motor.

← Xem tất cả mã lỗi OKI MC573dn

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie