Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi E202-0002 — Canon iR Advance C350i

Code: E202-0002

Description: Scanner Unit HP error
The HP of the Scanner Unit could not be detected when completing scanning operation.
Remedy: [Related parts] - Harnesses from the Reader Assembly HP Sensor to the Main Controller PCB 1. Reader Assembly HP Sensor (PS01/J913) to Relay Connector (3P) (Unit of replacement: CABLE, HOME POSITION SENSOR) 2. Relay Connector (3P) to Main Controller PCB (UN81/J8103) (Unit of replacement: CABLE, READER MAIN) - Harness between the Reader Motor (M01/J901) and the Main Controller PCB (UN81/J8103) (Unit of replacement: CABLE, READER MAIN) - Reader Motor (M01) (Unit of replacement: MOTOR, STEPPING) - CIS HP Sensor (PS01) (Unit of replacement: PHOTO INTERRUPTER) - BOOK Motor (Unit of replacement: MOTOR, STEPPING) - Pulley Gear 85T/20T (Unit of replacement: GEAR, 85T/20T) - Carriage Timing Belt (Unit of replacement: BELT, TIMING, COGGED) - Idler Pulley (Unit of replacement: PULLEY, IDLER) - Idler Pulley Holder (Unit of replacement: READER ASSEMBLY) - FB Shaft (Unit of replacement: READER ASSEMBLY) - Electrolytic capacitor on the Main Controller PCB (C8002) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) - 24V power supply for driving the Reader on the Main Controller PCB side (J7003/pin 1) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) - Harness between the Main Controller PCB (UN81/J7003) and the Low-voltage Power Supply PCB (UN01/J313) (Unit of replacement: CABLE, POWER SUPPLY) - Low-voltage Power Supply PCB (UN01) (Unit of replacement: POWER SUPPLY ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the harness between the Reader Assembly HP Sensor and the Main Controller PCB. 2. Check the harness between the Reader Motor and the Main Controller PCB. 3. At initial operation of the Reader startup after the main power is turned ON, check if the Reader Motor operates (whether the Scanner Unit moves or operation sound is heard). If it operates, move the Carriage Timing Belt by hand and check if load is appropriate. a. If it is appropriate, replace the CIS HP Sensor. b. If it is not appropriate (overloaded), replace the following parts. - Stepping Motor - Z85_T20 Pulley Gear - Carriage Timing Belt - Idler Pulley - Idler Pulley Holder 4. Check for soiling or scar on the surface of the FB Shaft on which the Scanner Unit is installed. If there is soiling or scar, replace the FB Shaft. 5. Measure the electrolytic capacitor on the Main Controller PCB using a tester. If the measurement value is 24V, replace the Main Controller PCB. 6. Measure the 24V power supply for driving the Reader on the Main Controller PCB side using a tester. If the measurement value is 24 V, replace the Main Controller PCB. 7. Check the harness between the Main Controller PCB and the Low-voltage Power Supply PCB. 8. Perform step 6 again. If the measurement value is 24 V, replace the Low-voltage Power Supply PCB.

← Xem tất cả mã lỗi Canon iR Advance C350i

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie