Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 148.01 ... 148.08 — Lexmark X736

Code: 148.01 ... 148.08

Description: Motor Error The multipurpose feeder motor has failed.
Remedy: 1 1. Open the rear frame cover. 2. Reseat JDX1 cable. Does the problem persist? Go to step 2. Problem resolved. 2 1. Remove the tray. 2. Check the MPF/duplex gear for any damage. 3. Check if the MPF/duplex gear can engage the duplex drive gear. 4.Manually turn the gear and check for any damage. Does the error still exist? Replace the MPF/duplex gear. See “Multipurpose feeder (MPF)/duplex gear and housing removal”. Go to step 3. 3 1. Open the front door cover. 2. Disengage the duplex belt connecting to duplex drive gear/duplex rollers. The duplex reference edge assembly should not turn for isolation. 3. Remove the input tray. 4. Bring the printer up in Diagnostics Menu (Turn off the printer, press and hold buttons 3 and 6, then turn on the printer). 5. Navigate to MOTOR TESTS > Duplex > Forward or Reverse. 6. Navigate to MOTOR TESTS > MPF Test> Forward or Reverse. Does the error still exist? Go to step 4. Go to step 7. 4 1. Connect a new MPF motor with cable to the JDX1 connector on the system board from outside of the machine. 2. Bring the printer up in Diagnostics Menu (Turn off the printer, press and hold buttons 3 and 6, then turn on the printer). 3. Navigate to MOTOR TESTS > Duplex > Forward or Reverse. Note: Perform this test for 5 to 10 seconds only. 4. Navigate to MOTOR TESTS > MPF Test> Forward or Reverse. Note: Perform this test for 5 to 10 seconds only. 5. Check if the motor would turn for each test. Does this clear the problem? Go to step 5. Replace the system board. See “System board removal”. 5 1. Disconnect the MPF motor cable on the motor side. 2. Connect a new motor from outside of the machine. 3. Bring the printer up in Diagnostics Menu (Turn off the printer, press and hold buttons 3 and 6, then turn on the printer). 4. Navigate to MOTOR TESTS > Duplex > Forward or Reverse. Note: Perform this test for 5 to 10 seconds only. 5. Navigate to MOTOR TESTS > MPF Test> Forward or Reverse. Note: Perform this test for 5 to 10 seconds only. 6. Check if the motor would turn for each test. Does the error still exist? Go to step 6. Replace the MPF duplex motor assembly. See “Multipurpose feeder (MPF)/duplex motor assembly removal”. 6 Connect a new MPF motor cable to the old MPF motor and connect it to JDX1 connector on the system board. Does the error still exist? Go to step 7. Replace the MPF/duplex motor cable. See “Multipurpose feeder (MPF)/duplex motor cable removal”. 7 1. Open the front door cover. 2. Check the duplex reference edge guide assembly for any damage. 3. Check rollers and belts for damage and misalignment. 4. Bring the printer up in Diagnostics Menu (Turn off the printer, press and hold buttons 3 and 6, then turn on the printer). 5. Remove the input tray. 6. Navigate to MOTOR TESTS > Duplex > Forward. 7. Check if the duplex assembly runs. 8. Check if the MPF/duplex gear turns. Is the duplex reference edge guide assembly free of damage? Replace the duplex reference edge guide assembly. See “Duplex reference edge guide assembly removal”. Go to step 8. 8 1. Check the front door assembly gears that engages to the MPF/duplex gear for any damage. 2. Close the front door assembly and open the front door cover. 3. Check if the front door cover assembly gears can engage the MPF/duplex gear. 4.Manually turn the gears. 5. Check the front door assembly for any damage. Is the front door assembly gear or the front door assembly damaged? Replace the front door assembly. See “Front door assembly removal”. Go to step 9. 9 1. Check the MPF tray for any damage. 2.Manually turn the MPF gear on the tray, and check if the MPF pick arm assembly would turn. 3. Bring the printer up in Diagnostics Menu (Turn off the printer, press and hold buttons 3 and 6, then turn on the printer). 4. Lift the MPF pick arm using the lever. 5. Select MOTOR TESTS > MPF > Forward. 6. Check if the pick arm would turn. Is the MPF pick arm assembly free of damage? Go to step 10. Replace the input tray. 10 Remove the input tray and insert a new one. Does this fix the problem? Problem resolved. Replace the system board. See “System board removal”.

← Xem tất cả mã lỗi Lexmark X736

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie