Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 374.60, 374.61 — Lexmark XC8160dtfe

Code: 374.60, 374.61

Description: 374.60 The motor (standard bin elevator) did not turn on. 374.61 The motor (standard bin elevator) did not turn off.
Remedy: Step 1 a Check the MSHPF for proper installation, and then check its paper path. See “Procedure before starting the MSHPF service checks”. b Enter the Diagnostics menu, select Output bin quick feed > select bin, and then touch Single or Continuous. Does the problem remain? Go to step 2. The problem is solved. Step 2 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Motor tests > Finisher > Standard bin elevator b Touch Start. Does the motor run? Go to step 5. Go to step 3. Step 3 Reseat the motor cable, and then check the motor for misalignment and damage. Is the motor properly installed and free of damage? Go to step 5. Go to step 4. Step 4 Reinstall or replace the motor. See “Motor (standard bin elevator) removal”3. Does the problem remain? Go to step 5. The problem is solved. Step 5 Check the standard bin elevator drive for misalignment and damage. Is the elevator drive properly installed and free of damage? Go to step 7. Go to step 6. Step 6 Reinstall or replace the elevator drive. See “Standard bin elevator drive removal”2. Does the problem remain? Go to step 7. The problem is solved. Step 7 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Sensor tests > Finisher b Find the sensor (Standard bin lower limit). Does the sensor status change while toggling the sensor? Go to step 10. Go to step 8. Step 8 Reseat the sensor cable, and then check the sensor for misalignment and damage. Is the sensor properly installed and free of damage? Go to step 10. Go to step 9. Step 9 Reinstall or replace the sensor. Does the problem remain? Go to step 10. The problem is solved. Step 10 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Sensor tests > Finisher b Find the sensor (Standard bin stack upper limit 1). Does the sensor status change while toggling the sensor? Go to step 13. Go to step 11. Step 11 Reseat the sensor cable, and then check the sensor for misalignment and damage. Is the sensor properly installed and free of damage? Go to step 13. Go to step 12. Step 12 Reinstall or replace the sensor. See “Sensor (standard bin stack upper limit) removal”1. Does the problem remain? Go to step 13. The problem is solved. Step 13 a Enter the Diagnostics menu, and then navigate to: Output device diagnostics > Sensor tests > Finisher b Find the sensor (Standard bin paper present). Does the sensor status change while toggling the sensor? Go to step 16. Go to step 14. Step 14 Reseat the sensor cable, and then check the sensor and its actuator for misalignment and damage. Is the sensor properly installed and free of damage? Go to step 6. Go to step 15. Step 15 Reinstall or replace the sensor. See “Sensor (standard bin paper present) removal”4. Does the problem remain? Go to step 16. The problem is solved. Step 16 Check the MSHPF standard bin for misalignment and damage. Note: Make sure that the shaft aligns with the gear. Is the bin properly installed and free of damage? Go to step 17. Go to step 19. Step 17 Turn the elevator gears and check if the bin moves from top to bottom. Does the bin properly move? Go to step 20. Go to step 18. Step 18 Remove the obstructions along the bin path. Does the problem remain? Go to step 19. The problem is solved. Step 19 Reinstall or replace the bin. Does the problem remain? Go to step 20. The problem is solved. Step 20 Check the standard bin elevator gear for misalignment and damage. Is the gear properly installed and free of damage? Go to step 22. Go to step 21. Step 21 Reinstall or replace the gear. Does the problem remain? Go to step 22. The problem is solved. Step 22 Check the standard bin elevator belt for misalignment and damage. Note: Make sure that there are no other parts interfering with the movement of the belt. Is the belt properly installed and free of damage? Go to step 24. Go to step 23. Step 23 Reinstall or replace the belt. Does the problem remain? Go to step 24. The problem is solved. Step 24 Check the standard bin elevator belt holder for misalignment and damage. Note: Make sure that the elevator belt is properly engaged with the holder. Is the belt properly installed and free of damage? Go to step 26. Go to step 25. Step 25 Reinstall or replace the belt holder. Does the problem remain? Go to step 26. The problem is solved. Step 26 Check the pulley gears for misalignment and damage. Note: Make sure that the pin is properly installed. Are the pulley gears properly installed and free of damage? Go to step 28. Go to step 27.

← Xem tất cả mã lỗi Lexmark XC8160dtfe

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie