Description: When printing from paper tray 3 to 5, the T3(LT or TT) paper feed sensor detected open paper tray 3 (after registering printing data to engine).
Remedy: • Close the appropriate paper tray correctly. 1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 3 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 4 TT relay PCB failure Replace a TT relay PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.
Description: When printing from paper tray 4 to 5, the T4(LT or TT) paper feed sensor detected open paper tray 4 (after registering printing data to engine).
Remedy: • Close the appropriate paper tray correctly. 1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 3 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 4 TT relay PCB failure Replace a TT relay PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.
Description: Machine stack sensor detected the ejected paper full state at the start of printing.
Remedy: • Remove the paper from the machine output tray. 1 Machine stack actuator coming off or caught in some sections of the machine Reattach the machine stack actuator. 2 Machine stack sensor failure Replace the machine stack sensor. 3 Main PCB failure Replace the main PCB ASSY.
Description: The back cover/duplex tray sensor detected that the cover was open when duplex printing is started. (Before registering printing data to engine)
Remedy: • Close the back cover correctly. • Attach the duplex tray correctly. 1 Back cover/duplex tray sensor attachment failure Reattach the back cover/duplex tray sensor. 2 Connection failure of the back cover/duplex tray sensor harness Reconnect the back cover/duplex tray sensor harness. 3 Damaged back cover Replace the back cover. 4 Damaged duplex tray Replace the duplex tray. 5 Main PCB failure Replace the main PCB ASSY.
Description: The back cover/duplex tray sensor detected that the cover was open during duplex printing. (After registering printing data to engine)
Remedy: • Close the back cover correctly. • Attach the duplex tray correctly. 1 Back cover/duplex tray sensor attachment failure Reattach the back cover/duplex tray sensor. 2 Connection failure of the back cover/duplex tray sensor harness Reconnect the back cover/duplex tray sensor harness. 3 Damaged back cover Replace the back cover. 4 Damaged duplex tray Replace the duplex tray. 5 Main PCB failure Replace the main PCB ASSY.
Description: The registration rear sensor detected that the paper fed was smaller or larger than the specified size in duplex printing mode.
Remedy: • Use specified paper. 1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 high-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.
Description: Detected that the TT was not turned ON.
Remedy: • Turn ON the TT. • Reconnect the AC cord of the TT. 1 Malfunction of the TT control PCB Install the latest main firmware. 2 Connection failure of the TT lowvoltage power supply PCB harness Reconnect the TT low-voltage power supply PCB harness. 3 TT AC cord breakage Replace the AC cord. 4 TT low-voltage power supply PCB failure Replace the TT low-voltage power supply PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.
Description: Detected that the size of the paper set to paper tray was over 10 mm shorter than letter size when receiving fax or printing a list/report.
Remedy: • Set A4 or Letter-size paper. 1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.