Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Brother MFC-L5850DW — Trang 3/19

Code: 050C

Description: When the center thermistor of the fuser unit was higher than the idle temperature, the side thermistor detected a temperature lower than the specified temperature.
Remedy: 1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

Code: 0800

Description: An error occurred in the internal temperature sensor.
Remedy: 1 Connection failure of the internal temperature sensor harness Reconnect the internal temperature sensor harness. 2 Internal temperature sensor failure Replace the main frame L ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Code: 0900

Description: Detected irregular power supply for more than 100 times.
Remedy: 1 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. Reset counters for consumable parts (function code: 88) to reset the irregular power supply detection counter after the replacement. 2 Main PCB failure Replace the main PCB ASSY. Note: • The irregular power supply detection error of the low-voltage power supply PCB (error code: 0900) occurs when there is a large distortion in the power supply voltage supplied to the machine. In this case, if the same power supply is used, the same error may occur even when the low-voltage power supply PCB ASSY is replaced. Ask the user to review the installation environment. • Do not reset the power supply PCB counter before replacing it with a new one. It may cause fire.

Code: 0A02

Description: Detected a main fan failure.
Remedy: 1 Connection failure of the main fan harness Reconnect the main fan harness. 2 Connection failure of the toner amount detection sensor PCB harness (light emission) Reconnect the toner amount detection sensor PCB harness (light emission). 3 Main fan failure Replace the main fan. 4 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 5 Toner amount detection sensor PCB (light emission) failure Replace the toner amount detection sensor PCB ASSY (light emission). 6 Main PCB failure Replace the main PCB ASSY.

Code: 0B01

Description: An error occurred in the high-voltage power supply PCB ASSY while operating.
Remedy: 1 Connection failure of the HVPS flat cable Reconnect the HVPS flat cable. 2 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Code: 0B02

Description: An error occurred in the high-voltage power supply PCB ASSY when the machine was in the ready state.
Remedy: 1 Connection failure of the HVPS flat cable Reconnect the HVPS flat cable. 2 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Code: 1701

Description: Detected a TT fan failure.
Remedy: 1 Malfunction of the TT control PCB Install the latest main firmware. 2 Connection failure of the TT fan harness Reconnect the TT fan harness. 3 LT/TT connector failure (machine side or TT side) Replace the LT/TT connector of the machine side or TT side. 4 TT fan failure Replace the TT fan. 5 TT control PCB failure Replace the TT control PCB. 6 Main PCB failure Replace the main PCB ASSY.

Code: 1801

Description: A communication error occurred between the ASIC and T2LT control PCB in the engine. (LT only)
Remedy: 1 Malfunction of the LT control PCB Install the latest main firmware. 2 An LT/TT connector failure (machine side or LT side) Replace the appropriate LT/TT connector of the machine side or LT side. 3 An LT control PCB failure Replace the appropriate LT control PCB. 4 Main PCB failure Replace the main PCB ASSY.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie