• Code: 2570 ... 257C
• Display: Ink insufficient. Press OK and replace ink tank.
• Description: Ink tank short on ink A suction operation was attempted, but there is not enough ink left in the tank for the operation (iPF8000 series, iPF9000 series). Reference) About 5 mL to 40 mL of ink may have been left in the tank when this warning occurs. 70:Bk, 71:Y, 72:M, 73:C, 74:PM, 75:PC, 76:MBk1, 77:MBk2, 78:GY, 79:PGY, 7A:R, 7B:B, 7C:G
• Remedy: 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)

• Code: 2580 ... 258C
• Display: Ink insufficient. Press OK and replace ink tank. Ink insufficient. Replace ink tank.
• Description: Ink tank short on ink A suction operation was attempted, but there is not enough ink left in the tank for the operation. (In the small LCD, the lower arrow points to the color in question.) Reference) About 5 mL to 40 mL of ink may have been left in the tank when this warning occurs. 80:Bk, 81:Y, 82:M, 83:C, 84:PM, 85:PC, 86:MBk1, 87:MBk2, 88:GY, 89:PGY, 8A:R, 8B:B, 8C:G
• Remedy: 1. Replace the ink. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)

• Code: 2590 ... 259C
• Display: Ink insufficient. Press OK and replace ink tank. Ink insufficient. Replace ink tank.
• Description: Ink tank short on ink A print operation was attempted, but there is not enough ink left in the tank for the operation. (In the small LCD, the lower arrow points to the color in question.) Reference) About 5 mL to 40 mL of ink may have been left in the tank when this warning occurs. 90:Bk, 91:Y, 92:M, 93:C, 94:PM, 95:PC, 96:MBk1, 97:MBk2, 98:GY, 99:PGY, 9A:R, 9B:B, 9C:G (*1) 259C: 03810208-259C
• Remedy: 1. Replace the ink. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)

• Code: 259C ... 25A8
• Display: Ink insufficient. Press OK and replace ink tank. Ink insufficient. Press OK and replace ink tank.
• Description: Ink insufficient in inktank. The amount of ink left in the inktank is insufficient for printing. (In the small LCD, the lower arrow points to the correspondence color.) Reference) There are the cases that about 5ml to 40ml ink is left in a inktank at warning occurs. 9C:Bk,9D:C,9E:M,9F:Y,A0:PC,A1:PM,A 2:MBk1,A3:MBk2, A4:GY,A5:PGY,A6:R,A7:G,A8:B (*2) 259C: 03810104-259C
• Remedy: 1. Replace inktank 2. Failure of detecting the ink amount left in the inktank. (Replace the supply unit /check the bundled wires.)

• Code: 25B7
• Display: Close the ink tank cover. Unable to detect ink level correctly. Unable to detect ink level correctly.
• Description: The remaining ink falls below the pin check level while ink tank cover is open.
• Remedy: Close the ink tank cover. Note) It does not recover if the cover is open when replacing the ink tank with a valid one. If removing the ink tank with lower ink remains (LIR) than Supply Pin in this situation, an error is detected. Also when keeping printing in this situation, if empty subtank corresponding to the ink tank with LIR is detected, the error shifts from ink tank with LIR to empty subtank.

• Code: 260E
• Display: Hardware error. 03130031-260E Turn off printer, wait, then turn on again.
• Description: Gap detection failure Carriage gap calibration has not been carried out, or gap detection is disabled by corrupt calibration data.
• Remedy: 1. Check to see if the multisensor reference plate (white patch for batch correction) is not soiled and perform GAP CALIB (if soiled, adjust the part after replacing it). 2. Replace the multisensor and perform GAP CALIB. 3. Replace the carriage unit and perform GAP CALIB.

• Code: 260F
• Display: Gap error. Turn off printer.
• Description: Gap reference plane error Request to replace an abnormal reference plane sheet (only in Service mode).
• Remedy: Check the multisensor reference plate (for soiling and faulty mounting).

• Code: 2800
• Display: No printhead Install printhead.
• Description: Printhead [X] non-existing [X]: Double-head model : The R-head does not exist. Single-head model: The head does not exit.
• Remedy: 1. Check the status of the printhead mounted. 2. Mount the long flexible cable and check the status of the cable being locked.