Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iPF9000 — Trang 16/39

Code: 291B

Display: Hardware error. 03130031-291B Turn off printer, wait, then turn on again.
Description: Lift shift timeout A lift operation has been executed, but no sensor has been detected or a sensor has remained detected.
Remedy: 1. Switch off the printer, then back on. 2. The carriage cannot travel to the lift drive position. 3. The lift drive cam is not engaged. 4. Faulty lift drive sensor 5. Faulty lift drive motor

Code: 291D

Display: Hardware error. 03130031-291D Turn off printer, wait, then turn on again.
Description: Spur cam sensor detection failure
Remedy: Check the spur cam sensor in I/O mode. -If OK, check the lifter drive system. -If NG, replace the sensor.

Code: 2920

Display: Media Take-up error. Check the paper. Press Online to clear error.
Description: Cannot take up paper An error check has been made on paper after the paper had been fed 1850 mm, but the media take-up unit was not driven at all in that interval (up to about 3700 mm [when run immediately after the start of detection]).
Remedy: 1. Check to see if the media take-up unit is switched on with the lock lever down. 2. Check the connection between the main unit and the media take-up unit. 3. Check to see if the wait roller is properly set. 4. Check to see if the media take-up detection sensor is shielded by paper when it is presented. 5. Faulty media take-up detection sensor 6. Faulty Media take-up motor

Code: 2921

Display: Rewinding error. Check for jam at indicated position. Press Online to clear error. Rewinding error. Check for jam at indicated position.
Description: Continued rewinding error The media take-up unit has continued rewinding for 10 seconds, with the media take-up paper detection sensor turned on, at printer power-on and at the start of printing.
Remedy: 1. Check to see if any obstacle is placed at the media take-up paper detection sensor position. 2. Faulty media take-up paper detection sensor 3. Faulty media take-up button 4. Faulty media take-up motor

Code: 2930

Display: Cutting Mode not Automatic. Remove stacker and print again or cancel and change settings. Print again Cancel
Description: Stacker is not ready. - The power supply is not supplied to the stacker. - The distance between the stacker and printer is not appropriate. - The stacker is not joined. - Stacker initial error
Remedy: Continue or stop the print. If the preparation of the stacker isn't performed, the error occurs again.

Code: 2931

Display: Cutting Mode not Automatic. Remove stacker and print again or cancel and change settings. Print again Cancel
Description: When the stacker is usable condition, the printing has been started at the setting of cut-off or cutline print or eject or manual mode.
Remedy: Print again after separating the distance between the stacker and printer enoughly, or cancel print.

Code: 2E00

Display: Load Roll Media
Description: Paper mismatch (roll paper) No roll paper have been fed when a job with a roll paper specification is received.
Remedy: Load roll paper.

Code: 2E01

Display: Roll printing is selected. Press Load/Eject and load a roll.
Description: Paper mismatch (roll paper) Roll Paper have not been fed when an internal print job having a roll paper specification started (during internal printing).
Remedy: Load roll paper.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie