• Code: 2408
• Display: Borderless printng not possible. Check supported paper.
• Description: At the start of borderless printing, roll paper whose size doesn't support borderless printing has been loaded.
• Remedy: Replace with appropriate paper.

• Code: 2409
• Display: Paper position is not suitable for borderless printing. Check paper position. Print to normal printing. Stop printing.
• Description: Invalid paper loading position (suspended job/ borderless printing) All of the following conditions were met. -Borderless printing data has been received. -Roll paper whose paper loading position is not suitable for borderless printing has been loaded. -The right or left edge of roll paper is more than 1mm off the prescribed position of the pre-ejection opening.
• Remedy: Reload/ replace the roll paper. Check roll paper. 1) Select "Normal printing. (No borderless printing)" and enforce printing. Borderless print setting is ignored. Print with default margin. Default margin depends on selected feeding trays and media type. 2) Select "Stop printing" or press "stop button"to stop printing. 3) Select "replace printing" or release releasing lever.

• Code: 240A
• Display: Borderless printing is not possible. Check supported paper. Check paper position. Print to normal printing. Stop printing.
• Description: Borderless printing is not possible (suspended job/ unsupported size). All of the following conditions are met. -Borderless printing data has been received. -Roll paper not supporting borderless printing has been loaded.
• Remedy: Reload/ replace the roll paper. Check roll paper. 1) Select "Normal printing. (No borderless printing)" and enforce printing. Borderless print setting is ignored. Print with default margin. Default margin depends on selected feeding trays and media type. 2) Select "Stop printing" or press "stop button"to stop printing. 3) Select "replace printing" or release releasing lever.

• Code: 2500 ... 250C
• Display: Ink tank is empty. Press OK and replace ink tank. No ink left. Replace ink tank.
• Description: Ink tank empty (continued use not allowed) The ink tank has run out of ink. (The reserved volume of ink is put to use after the remaining ink falls below the pin check level.) (In the small LCD, the lower arrow points to the color in question.) The last 2 digits signify applicable colors. 00:Bk, 01:Y, 02:M, 03:C, 04:PM, 05:PC, 06:MBk1, 07:MBk2, 08:GY, 09:PGY, 0A:R, 0B:B, 0C:G
• Remedy: 1. Replace the tank. 2. If the problem persists after the tank has been replaced, the remaining ink detection system is at fault (replace the supply unit or check the bundled wires).

• Code: 2510 ... 251C
• Display: Ink level is unknown. Check ink level. Press Online to start printing.
• Description: Remaining ink level unknown (continued use allowed) The level of ink remaining in the tank is detected when the tank cover is closed. Consumption has exceeded the original ink capacity (mismatch detected). Refill ink may have been used. (In the small LCD, the lower arrow points to the color in question.) The last 2 digits signify applicable colors. 10:Bk, 11:Y, 12:M, 13:C, 14:PM, 15:PC, 16:MBk1, 17:MBk2, 18:GY, 19:PGY, 1A:R, 1B:B, 1C:G
• Remedy: Replace the ink tank.

• Code: 2520 ... 252C
• Display: No ink tank loaded. Press OK and check ink tank. No ink tank loaded. Check ink tank.
• Description: Ink tank not installed (continued use not allowed) On a model that is furnished with a subtank, this error is indicated if the subtank has run out of ink and the state of an ink tank not being installed is detected. The last 2 digits signify applicable colors. 20:Bk, 21:Y, 22:M, 23:C, 24:PM, 25:PC, 26:MBk1, 27:MBk2, 28:GY, 29:PGY, 2A:R, 2B:B, 2C:G
• Remedy: 1. Remove and then reinstall the tank. 2. Replace the tank. 3. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)

• Code: 2540 ... 254C
• Display: Ink tank error. Press OK and replace ink tank.
• Description: Ink tank ID error The type of ink tank is wrong. The last 2 digits signify applicable colors. 40:Bk, 41:Y, 42:M, 43:C, 44:PM, 45:PC, 46:MBk1, 47:MBk2, 48:GY, 49:PGY, 4A:R, 4B:B, 4C:G
• Remedy: 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)

• Code: 2560 ... 256C
• Display: Ink tank error. Press OK and replace ink tank.
• Description: Ink tank EEPROM error There is an error in tank EEPROM. The last 2 digits signify applicable colors. 60:Bk, 61:Y, 62:M, 63:C, 64:PM, 65:PC, 66:MBk1, 67:MBk2, 68:GY, 69:PGY, 6A:R, 6B:B, 6C:G
• Remedy: 1. Replace the tank. 2. Failure of remaining ink detection system. (Replace the supply unit /check the bundled wires.)