Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance 4045A

Code: E000-0001

Description: Fixing temperature abnormal rise
The temperature detected by the main thermistor does not rise to the specified value during startup control.
Remedy: 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR; and then turn OFF and then ON the power. 2. Check connection of the Connectors (Thermistor Connector: J2063/J2510/J214, AC Connector: J105). 3. Replace the Fixing Main Thermistor (Film Unit). 4. Replace the Fixing Main Unit. 5. Replace the DC Controller PCB (UN2).

Code: E001-0000

Description: Fixing unit temperature rise detection
The reading of the main thermistor is 250 deg C or more continuously for 200 msec.
Remedy: 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR; and then turn OFF and then ON the power. 2. Check connection of the Connectors (Thermistor Connector: J2063/J2510/J214, AC Connector: J105). 3. Replace the Fixing Main Thermistor (Film Unit). 4. Replace the Fixing Main Unit. 5. Replace the DC Controller PCB (UN2).

Code: E001-0001

Description: Fixing unit temperature rise detection
The hardware circuit detects overheating of the main or sub thermistor for 30 msec.
Remedy: 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR; and then turn OFF and then ON the power. 2. Replace the DC Controller PCB (UN2).

Code: E001-0002

Description: Fixing unit temperature rise detection
The reading of the sub thermistor is 295 deg C or more continuously for 200 msec.
Remedy: 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR; and then turn OFF and then ON the power. 2. Check connection of the Connectors (Thermistor Connector: J2063/J2510/J214, AC Connector: J105). 3. Replace the Fixing Main Thermistor (Film Unit). 4. Replace the Fixing Main Unit. 5. Replace the DC Controller PCB (UN2).

Code: E002-0000

Description: Fixing unit temperature insufficient rise
1. The reading of the main thermistor is less than 115 deg C continuously for 400 msec 2.5 sec after it has indicated 100 deg C. 2. The reading of the main thermistor is less than 150 deg C continuously for 400 msec 1.3 sec after it has indicated 140 deg C.
Remedy: 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR; and then turn OFF and then ON the power. 2. Check connection of the Connectors (Thermistor Connector: J2063/J2510/J214, AC Connector: J105). 3. Replace the Fixing Main Thermistor (Film Unit). 4. Replace the Fixing Main Unit. 5. Replace the DC Controller PCB (UN2).

Code: E003-0000

Description: Low fixing temperature detection after standby
The reading of the main thermistor is less than 100 deg C continuously for 200 msec or more.
Remedy: 1. Go through the following to clear the error: COPIER> FUNCTION> CLEAR> ERR; and then turn OFF and then ON the power. 2. Check connection of the Connectors (Thermistor Connector: J2063/J2510/J214, AC Connector: J105). 3. Replace the Fixing Main Thermistor (Film Unit). 4. Replace the Fixing Main Unit. 5. Replace the DC Controller PCB (UN2).

Code: E004-0000

Description: Thermistor disconnection detection error
When disconnection is detected with connector for 30 sec continuously.
Remedy: 1. Check connection of the Connector (J2063/J2510/J214). 2. Replace the Film Unit. 3. Replace the Fixing Main Unit. 4. Replace the DC Controller PCB (UN2).

Code: E010-0001

Description: Unstable rotation of the Main Motor (M1)
Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec.
Remedy: 1. Check connection of the Connector (J2002/J2255/J203). 2. Replace the Main Motor (M1). 3. Replace the DC Controller PCB (UN2).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie