Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance C2220i — Trang 26/45

Code: E505-0001

Description: EEPROM error
The checksum for the EEPROM data has an error.
Remedy: Replace the finisher controller PCB.

Code: E514-8001

Description: Rear end assist home position error
The stapler does not leave the rear end assist home position when the rear end assist motor has been driven for 3 seconds.
Remedy: 1. The rear end assist home position sensor (PI109) is faulty. 2. The wiring between the finisher controller PCB and rear end assist motor is faulty. 3. The end assist mechanism is faulty. 4. The rear end assist motor (M109) is faulty. 5. The finisher controller PCB is faulty.

Code: E514-8002

Description: Rear end assist home position error
The stapler does not return to the rear end assist home position when the rear end assist motor has been driven for 3 seconds.
Remedy: 1. The rear end assist home position sensor (PI109) is faulty. 2. The wiring between the finisher controller PCB and rear end assist motor is faulty. 3. The end assist mechanism is faulty. 4. The rear end assist motor (M109) is faulty. 5. The finisher controller PCB is faulty.

Code: E517-0001

Description: Decurler HP detection error (at intrusion amount control)
The HP was not detected within the specified period of time (2 seconds) since the start of the decurler HP detection.
Remedy: 1. Check that the cam of the Decurler Roller is installed properly. 2. Replace the Decurler Motor. 3. Replace the Buffer Driver PCB. 4. Replace the DC Controller PCB.

Code: E519-0002

Description: Gear change home position error
The gear change home position sensor does not turn ON when the gear change motor has been driven for 387 pulses.
Remedy: 1. The gear change home position sensor (PI117) is faulty. 2. The wiring between the finisher controller PCB and gear change motor is faulty. 3. The gear change mechanism is faulty. 4. The gear change motor (M110) is faulty. 5. The finisher controller PCB is faulty.

Code: E519-8001

Description: Gear change home position error
The gear change home position sensor does not turn OFF when the gear change motor has been driven for 387 pulses.
Remedy: 1. The gear change home position sensor (PI117) is faulty. 2. The wiring between the finisher controller PCB and gear change motor is faulty. 3. The gear change mechanism is faulty. 4. The gear change motor (M110) is faulty. 5. The finisher controller PCB is faulty.

Code: E520-0001

Description: Shift Motor fails to move from HP
At initial rotation, when the Motor rotates for specified period of time and cannot move from HP, it is detected as an error if the same symptom occurs again after the first retry
Remedy: 1. Check if the Motor (M4) Connector is physically removed. 2. Replace the Motor. 3. Check if the Shift Roller HP Sensor (S2) Connector is physically removed. 4. Replace the Shift Roller HP Sensor (S2).

Code: E520-0002

Description: Shift Motor fails to return to HP
At initial rotation, when the Motor rotates for specified period of time and cannot return to HP, it is detected as an error if the same symptom occurs again after the first retry.
Remedy: 1. Check if the Motor (M4) Connector is physically removed. 2. Replace the Motor. 3. Check if the Shift Roller HP Sensor (S2) Connector is physically removed. 4. Replace the Shift Roller HP Sensor (S2).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie