• Code: E719-0003
• Description: Coin vendor error
  A communication error with the coin vendor occurred during unit price acquisition at startup.
• Remedy: [Related parts] Cable between the charging management equipment and the host machine [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Reference] When operating the machine without the charging management equipment, execute “COPIER> FUNCTION> CLEAR> ERR”. (It is designed to generate an error to prevent the misuse by removing the charging management equipment.)

• Code: E719-0031
• Description: Card Reader communication error
  Communication with the Card Reader could not be established at startup.
• Remedy: [Related parts] - Harness between the Card Reader and the Main Controller PCB (UN81/J20) - Card Reader [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the cable between the Card Reader and the Main Controller PCB. 2. After removing the Card Reader, execute “COPIER> FUNCTION> CLEAR> CARD” and “ERR”. [Caution] Data related to card ID (department) is cleared.

• Code: E719-0032
• Description: Card Reader communication error
  Although communication with the Card Reader was possible at startup, it became unavailable in the middle of the communication.
• Remedy: - Harness between the Card Reader and the Main Controller PCB (UN81/J20) - Card Reader [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Check the cable between the Card Reader and the Main Controller PCB. 2. After removing the Card Reader, execute “COPIER> FUNCTION> CLEAR> CARD” and “ERR”. [Caution] Data related to card ID (department) is cleared.

• Code: E720-0000
• Description: Error due to non-compatible Finisher
  A finisher which cannot be connected to the host machine was connected.
• Remedy: [Remedy] Connect the Finisher (STAPLE FINISHER-S1) for this model.

• Code: E720-0100
• Description: Cassette Pedestal detection error
  Connection of the Cassette Pedestal could not be detected.
• Remedy: [Related parts] - Cassette Pedestal - Harness between the DC Controller PCB (UN04/J190) and the drawer connector (J5904) on the host machine side (Unit of replacement: OPTION CST. DRAWER ASSEMBLY) - Harness between the drawer connector (J5950) on the Cassette Pedestal side and the Cassette Module Controller PCB (UN101/J650) (Unit of replacement: DRAWER CABLE ASSEMBLY) - Drawer on the host machine side (Unit of replacement: OPTION CST. DRAWER ASSEMBLY) - Drawer on the Cassette Pedestal side (Unit of replacement: DRAWER CABLE ASSEMBLY) - Cassette Module Controller PCB (UN101) (Unit of replacement: CST. PEDESTAL CONT. PCB ASS’Y) - DC Controller PCB (UN04) (Unit of replacement: DC CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts.

• Code: E730-A006
• Description: PDL communication error
  Response from PDL could not be detected.
• Remedy: [Related parts] Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Select “Settings/Registration> Function Settings> Printer> Printer Settings> Utility> Initialize Printer”, and execute PDL reset processing. 2. Turn OFF and then ON the main power, and check whether the error is cleared. 3. Reinstall the system software. 4. Replace the Main Controller PCB.

• Code: E730-A007
• Description: Mismatch of PDL version
  Version of the host machine control software and version of PDL control software were different.
• Remedy: [Related parts] - Flash PCB (UN96) - Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. After deleting the system software using USB memory, reinstall it using SST or a USB memory. 2. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 3. Replace the Main Controller PCB.

• Code: E730-B013
• Description: PDL embedded font error
  Font data was corrupted.
• Remedy: [Related parts] - Flash PCB (UN96) - Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. After deleting the system software using USB memory, reinstall it using SST or a USB memory. 3. After replacing the Flash PCB, reinstall the system software using SST or a USB memory. 4. Replace the Main Controller PCB.