Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance C351iF — Trang 16/29

Code: E280-0005

Description: Scanner Unit communication error
1. The CIS for iR-ADV C250 was installed to iR-ADV C350. 2. The CIS for iR-ADV C350 was installed to iR-ADV C250.
Remedy: [Remedy] Replace the Scanner Unit (CIS01/CIS02) with the one for the model. (Unit of replacement: CONTACT IMAGE SENSOR ASSEMBLY) [Caution] The parts numbers of the Scanner Unit are different between iR-ADV C250 and C350. Be sure to use the correct one.

Code: E301-0001

Description: Reading light intensity error
1. Light intensity at shading was insufficient. 2. Light intensity when no light was emitted from CIS was too much
Remedy: [Related parts] - Flexible Cable between the Scanner Unit (CIS01, CIS02/ J911) and the Main Controller PCB (UN81/J8101) (Unit of replacement: CABLE, FLAT) - Scanner Unit (CIS01/CIS02) (Unit of replacement: CONTACT IMAGE SENSOR ASSEMBLY) - Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. [Caution] The parts numbers of the Scanner Unit are different between iR-ADV C250 and C350. Be sure to use the correct one.

Code: E301-0002

Description: Reading light intensity error
Image sampling for shading was not completed.
Remedy: [Related parts] - Flexible Cable between the Scanner Unit (CIS01, CIS02/ J911) and the Main Controller PCB (UN81/J8101) (Unit of replacement: CABLE, FLAT) - Scanner Unit (CIS01/CIS02) (Unit of replacement: CONTACT IMAGE SENSOR ASSEMBLY) - Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) [Points to note at work] When checking the harness/cable or connector, perform the following work. 1. Disconnect and then connect the connector to check that there is no bent pin and cable disconnection. 2. Visually check that the harness is not caught or open circuit. 3. If there is any error, replace the corresponding harness/cable. [Remedy] Check/replace the related parts. [Caution] The parts numbers of the Scanner Unit are different between iR-ADV C250 and C350. Be sure to use the correct one

Code: E315-0007

Description: Image processing device error
JBIG encode error.
Remedy: [Remedy] Replace the Main Controller PCB (UN81). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY)

Code: E315-000D

Description: Image processing device error
JBIG decode error.
Remedy: [Related parts] - Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) - HDD (Unit of replacement: HARD DISK DRIVE) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> “5”, and execute “HD-CLEAR”. Then, turn OFF and then ON the main power (so the current job is deleted). 3. After turning OFF the main power, replace the HDD and the Main Controller PCB at the same time. 4. Execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory.

Code: E315-000E

Description: Image processing device error
Error at software decoding.
Remedy: [Related parts] - Main Controller PCB (UN81) (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY) - HDD (Unit of replacement: HARD DISK DRIVE) [Remedy] Perform the following in the order while checking whether the error is cleared. 1. Turn OFF and then ON the main power, and check whether the error is cleared. 2. Select COPIER> FUNCTION> SYSTEM> CHK-TYPE> “5”, and execute “HD-CLEAR”. Then, turn OFF and then ON the main power (so the current job is deleted). 3. After turning OFF the main power, replace the HDD and the Main Controller PCB at the same time. 4. Execute [4] Clear/Format> [1] Disk Format (HDD format) using SST or a USB memory.

Code: E315-000F

Description: Image processing device error
Error at MemoryCopy
Remedy: [Remedy] Replace the Main Controller PCB (UN81). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY)

Code: E315-0027

Description: Image processing device error
ROTU timeout error.
Remedy: [Remedy] Replace the Main Controller PCB (UN81). (Unit of replacement: MAIN CONTROLLER PCB ASSEMBLY)
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie