Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance C5235 — Trang 6/56

Code: E012-3001

Description: Failure in control of Drum Motors in all colors
Controls of the Drum Motors (in all colors) are faulty at the same time.
Remedy: Check the Process Unit (to see if it’s properly installed). Check the Drum Unit (to see if it’s properly installed).

Code: E012-3002

Description: Failure in rotation of Drum Motor (in all colors) (M1,M2,M3,M4)
All of the Drum Motors are not rotating at the specified speed/are stopped.
Remedy: Check the connector on the Drum Driver PCB (UN4).

Code: E013-0001

Description: Error in Recycle Toner Stirring Motor
The motor failed to rotate at the specified speed.
Remedy: 1. Check disconnection of the Recycle Toner Stirring Motor (M14). 2. Check toner level in the Recycle Toner container (replace the Recycle Toner container if the toner level is too much). 3. Replace the Recycle Toner Stirring Motor. 4. Replace the Pickup Feed Driver PCB (UN2). 5. Replace the DC Controller PCB (UN1).

Code: E014-0001

Description: Error in Fixing Motor
The motor failed to rotate at the specified speed.
Remedy: 1. Check the Fixing Assembly. 2. Remove and then install the Fixing Assembly. 3. Replace the Film Unit. 4. Replace the Fixing Motor. 5. Replace the DC Controller PCB (UN1).

Code: E020-0011

Description: Error in Y Developing Assembly
Patch level is higher than the target upper limit although the patch level was minimized at the time of patch initialization.
Remedy: Go through the following: DISPLAY > P-LED-DA; perform cleaning first If P-LED-DA is 3F or more. 1. Check installation of the Developing Assembly and the Drum. 2. Clean the Patch Sensor (UN47,UN48,UN49) Window. 3. Replace the Patch Sensor. 4. Replace the Drum.

Code: E020-0012

Description: Error in M Developing Assembly
Patch level is higher than the target upper limit although the patch level was minimized at the time of patch initialization.
Remedy: Go through the following: DISPLAY > P-LED-DA; perform cleaning first If P-LED-DA is 3F or more. 1. Check installation of the Developing Assembly and the Drum. 2. Clean the Patch Sensor (UN47,UN48,UN49) Window. 3. Replace the Patch Sensor. 4. Replace the Drum

Code: E020-0013

Description: Error in C Developing Assembly
Patch level is higher than the target upper limit although the patch level was minimized at the time of patch initialization.
Remedy: Go through the following: DISPLAY > P-LED-DA; perform cleaning first If P-LED-DA is 3F or more. 1. Check installation of the Developing Assembly and the Drum. 2. Clean the Patch Sensor (UN47,UN48,UN49) Window. 3. Replace the Patch Sensor. 4. Replace the Drum.

Code: E020-0014

Description: Error in Bk Developing Assembly
Patch level is higher than the target upper limit although the patch level was minimized at the time of patch initialization.
Remedy: Go through the following: DISPLAY > P-LED-DA; perform cleaning first If P-LED-DA is 3F or more. 1. Check installation of the Developing Assembly and the Drum. 2. Clean the Patch Sensor (UN47,UN48,UN49) Window. 3. Replace the Patch Sensor. 4. Replace the Drum.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie