• Code: 5BB-8001-02
• Description: Error in the Waste Paper Full Sensor (Inner Booklet Trimmer-A1)
• Causes: The A/D input value does not enter into the D/A output upper limit of the Waste Paper Full Sensor.
• Remedy: [Related parts] - Harnesses from the Waste Paper Full Sensor (emitting/receiving) (S011) to the Trimmer Controller PCB - Waste Paper Full Sensor (emitting/receiving) (S011) - Trimmer Controller PCB (PCB1)

• Code: 5BB-8002-02
• Description: Error in the Waste Paper Full Sensor (Inner Booklet Trimmer-A1)
• Causes: The A/D input value does not enter into the D/A output lower limit of the Waste Paper Full Sensor.
• Remedy: [Related parts] - Harnesses from the Waste Paper Full Sensor (emitting/receiving) (S011) to the Trimmer Controller PCB - Waste Paper Full Sensor (emitting/receiving) (S011) - Trimmer Controller PCB (PCB1)

• Code: 5E1-8001-02
• Description: Tray Lift Motor failed to go through HP (Document Insertion / Folding Unit-K1/Document Insertion Unit-Q1)
• Causes: Paper Feed Sensor (S3) was not turned ON.
• Remedy: [Related parts] - Harnesses from the Inserter/Folder ContRoller PCB (PCB2) to the Paper Feed Sensor (S3) - Harnesses from the Inserter/Folder ContRoller PCB (PCB2) to the Tray Lift Motor (M2) - Inserter/Folder ContRoller PCB (PCB2) - Paper Feed Sensor (S3) - Tray Lift Motor (M2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When replacing the Inserter/Folder ContRoller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 5E1-8002-02
• Description: Tray Lift Motor failed to go through HP (Document Insertion / Folding Unit-K1/Document Insertion Unit-Q1)
• Causes: While the tray is moving down or initialization, the Folding belt HP sensor (S5) has not turned ON within the specified pulse.
• Remedy: [Related parts] - Harnesses from the Inserter/Folder ContRoller PCB (PCB2) to the Tray Lower Limit Sensor (S5) - Harnesses from the Inserter/Folder ContRoller PCB (PCB2) to the Tray Lift Motor (M2) - Inserter/Folder ContRoller PCB (PCB2) - Tray Lower Limit Sensor (S5) - Tray Lift Motor (M2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When replacing the Inserter/Folder ContRoller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 5F0-8001-02
• Description: a. Error in the Saddle Lead Edge Stopper Motor (Finisher-X1) b. Error in the Saddle Paper End Stopper Motor (Finisher-V)
• Causes: a. The Saddle Lead Edge Stopper HP Sensor does not detect the Saddle lead edge stopper when the Saddle lead edge stopper has been moved for 182 mm by Saddle Lead Edge Stopper Motor. b. The saddle paper end stopper does not come off the Saddle Paper End Stopper HP Sensor when the Saddle Paper End Stopper Motor has been driven for 1 second.
• Remedy: a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Lead Edge Stopper HP Sensor (S205) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Lead Edge Stopper Motor (M203) to the Saddle Stitcher Controller PCB - Saddle Lead Edge Stopper HP Sensor (S205) - Saddle Lead Edge Stopper Motor (M203) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paper End Stopper HP Sensor (PS210) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper End Stopper Motor (M206) to the Saddle Stitcher Controller PCB - Saddle Paper End Stopper HP Sensor (PS210) - Saddle Paper End Stopper Motor (M206) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 5F0-8002-02
• Description: a. Error in the Saddle Lead Edge Stopper Motor (Finisher-X1) b. Error in the Saddle Paper End Stopper Motor (Finisher-V)
• Causes: a. The Saddle lead edge stopper does not come off the Saddle Lead Edge Stopper HP Sensor when the Saddle Lead Edge Stopper Motor has been driven for 50 pulses. b. The Saddle Paper End Stopper HP Sensor does not detect the saddle paper end stopper when the Saddle Paper End Stopper Motor has been driven for 4 seconds.
• Remedy: a. STAPLE FIN-X1/BOOKLET FIN-X1 [Related parts] - Harnesses from the Saddle Lead Edge Stopper HP Sensor (S205) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Lead Edge Stopper Motor (M203) to the Saddle Stitcher Controller PCB - Saddle Lead Edge Stopper HP Sensor (S205) - Saddle Lead Edge Stopper Motor (M203) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> Action on parts replacement" in the Service Manual. b. STAPLE FIN-V/BOOKLET FIN-V [Related parts] - Harnesses from the Saddle Paper End Stopper HP Sensor (PS210) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Paper End Stopper Motor (M206) to the Saddle Stitcher Controller PCB - Saddle Paper End Stopper HP Sensor (PS210) - Saddle Paper End Stopper Motor (M206) - Saddle Stitcher Controller PCB (PCB201) - Finisher Controller PCB (PCB101) [Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection timing of this error, this error code may be displayed. Accordingly, perform the following work before checking the related parts. 1. Check whether there is not the mulfunction in the swing guide unit. 2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102). [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing the Parts" in the Service Manual.

• Code: 5F1-8001-02
• Description: Saddle Folder/Feeder Clock Error (Finisher-X1)
• Causes: The drive speed of the Saddle Folder/Feeder Motor is less than 5 mm/sec.
• Remedy: [Related parts] - Harnesses from the Saddle Folder/Feeder Motor Sensor (S214) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Folder/Feeder Motor (M206) to the Saddle Stitcher Controller PCB - Saddle Folder/Feeder Motor Sensor (S214) - Saddle Folder/Feeder Motor (M206) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.

• Code: 5F1-8002-02
• Description: Error in the Saddle Folder/Feeder Motor (Finisher-X1)
• Causes: The Saddle Folder HP Sensor does not detect the home position of the paper fold roller during initialization.
• Remedy: [Related parts] - Harnesses from the Saddle Folder HP Sensor (S229) to the Saddle Stitcher Controller PCB - Harnesses from the Saddle Folder/Feeder Motor (M206) to the Saddle Stitcher Controller PCB - Saddle Folder HP Sensor (S229) - Saddle Folder/Feeder Motor (M206) - Saddle Stitcher Controller PCB (PBA201) - Finisher Controller PCB (PBA101) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] When replacing the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual.