Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR Advance C7565i — Trang 78/112

Code: 677-0001-00

Description: Print server error
Causes: Abnormality detected on the exhaust fan operation of printer server
Remedy: 1. Check supplying power to the exhaust fan 2. Exhaust fan replacement

Code: 677-0003-00

Description: Print server error
Causes: An error in the fan of the Print Server was detected.
Remedy: [Related parts] R1.00 - Print Server Fan - Main Controller PCB [Remedy] Check/replace the related harness/cable, connector and parts.

Code: 677-0004-00

Description: Print server error
Causes: Abnormality detected on the CPU fan operation of printer server
Remedy: 1. Check supplying power to the CPU fan 2. CPU fan replacement

Code: 677-0010-00

Description: Print server error
Causes: Failure was detected in operation of the CPU fan on the print server.
Remedy: 1. Replace the board of the print server. 2. Reinstall the Print Server (For details, refer to "Service Manual image PASS P2.")

Code: 677-0080-00

Description: Print server error
Causes: Error is detected at the Mother Board check when print server is started.
Remedy: 1. Check the cable connection and turn OFF and then ON the power. 2. Reinstall the print server (For details, refer to "Service Manual image PASS P2.")

Code: 711-0001-05

Description: Communication error
Causes: An error was detected in IPC communication with the finisher.
Remedy: [Related parts] R1.00 - Harness between the DC Controller PCB (UN2/J1226) and the Finisher Lattice (J7512A) - Finisher Controller PCB - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Code: 711-0002-05

Description: Communication error
Causes: A block checksum error was detected in IPC communication with the finisher.
Remedy: [Related parts] R1.00 - Harness between the DC Controller PCB (UN2/J1226) and the Finisher Lattice (J7512A) - Finisher Controller PCB - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.

Code: 713-0001-05

Description: Communication error
Causes: Reception error was detected 3 consecutive times in communication with the finisher.
Remedy: [Related parts] R1.00 - Harness between the DC Controller PCB (UN2/J1226) and the Finisher Lattice (J7512A) - Finisher Controller PCB - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES - After replacement of the Finisher Controller PCB, refer to "Adjustments> Adjustment when Replacing the Parts" in the Service Manual for the Finisher.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie