Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR2850 — Trang 4/15

Code: E225-0002

Description: The edge gain correction level is different from the correction level for the preceding sheet by a specific level or more
Causes: The scanning lamp is faulty. The CCD PCB is faulty. The rear controller PCB is faulty.
Remedy: 1. Scanning lamp (LAMP1) Is the lamp ON during the initial operation after the main power switch is turned on? NO: Replace the scanning lamp. 2. CCD unit, Reader controller PCB Try replacing the CCD unit. Is the problem corrected? YES: End. NO: Replace the reader controller PCB.

Code: E240-0000

Description: A fault occurs in communication between the CPU of the main controller PCB and the CPU of the DC controller PCB
Causes: The main controller PCB is faulty. The DC controller PCB is faulty.
Remedy: 1. Wiring Is the wiring from the min controller PCB to the DC controller PCB normal? NO: Correct the wiring. 2. DC controller PCB, Main controlled PCB Try replacing the DC controller PCB. Is the problem corrected? YES: End. NO: Replace the main controller PCB.

Code: E243-0000

Description: A fault occurs in the communication between the CPU of the control panel PCB and the CPU of the main controller PCB
Causes: The control panel CPU PCB is faulty. The main controller PCB is faulty.
Remedy: 1. Wiring Is the wiring from the main controller PCB to the DC controller PCB normal? NO: Correct the wiring. 2. Control panel CPU PCB, Main controller PCB Try replacing the control panel CPU PCB. Is the problem corrected? YES: End. NO: Replace the main controller PCB.

Code: E248-0001

Description: A difference is discovered between the ID in EEPROM read when the main power switch is turned on and the ID in ROM upon comparison
Causes: The EEPROM (IC403) of the reader controller PCB is faulty. The reader controller PCB is faulty.
Remedy: 1. Execute the following in service mode: COPIER>FUNCTION>CLEAR>CON. Is the proem corrected? YES: End. After executing the service mode, be sure to enter the service mode data newly. 2. EE-PROM, Reader controller PCB Try replacing the EE-PROM. Is the problem corrected? YES: End. After replacement, be sure to enter the service mode data newly. NO: Replace the rear controller PCB. After replacement, be sure to enter the service mode date newly.

Code: E248-0002

Description: The data read does not match the data written to EEPROM
Causes: The EEPROM (IC403) of the reader controller PCB is faulty. The reader controller PCB is faulty.
Remedy: 1. Execute the following in service mode: COPIER>FUNCTION>CLEAR>CON. Is the proem corrected? YES: End. After executing the service mode, be sure to enter the service mode data newly. 2. EE-PROM, Reader controller PCB Try replacing the EE-PROM. Is the problem corrected? YES: End. After replacement, be sure to enter the service mode data newly. NO: Replace the rear controller PCB. After replacement, be sure to enter the service mode date newly.

Code: E248-0003

Description: A difference is discovered between the ID of EEPROM and the ID of ROM upon comparison while writing data
Causes: The EEPROM (IC403) of the reader controller PCB is faulty. The reader controller PCB is faulty.
Remedy: 1. Execute the following in service mode: COPIER>FUNCTION>CLEAR>CON. Is the proem corrected? YES: End. After executing the service mode, be sure to enter the service mode data newly. 2. EE-PROM, Reader controller PCB Try replacing the EE-PROM. Is the problem corrected? YES: End. After replacement, be sure to enter the service mode data newly. NO: Replace the rear controller PCB. After replacement, be sure to enter the service mode date newly.

Code: E261-0000

Description: The intervals of zero-cross signals deviate from the tolerance range while the fixing heater is supplied with power
Causes: The wiring is faulty (short circuit, open circuit). The main power supply PCB is faulty. The DC controller PCB is faulty.
Remedy: 1. Connectors Are the connector J205 on the main power supply PCB and the connector J308B on the DC controller PCB securely connected? (zero-cross signal: J205-7 <-> J308B-1) NO: Connect the connectors securely. 2. Main power supply PCB, Main controller PCB Try replacing the main power supply PCB. Is the problem corrected? YES: End. NO: Replace the DC controller PCB.

Code: E302-0001

Description: During shading, the shading processing does not end on the reader controller PCB after 1 sec
Causes: The CCD PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty.
Remedy: 1. Connector Are the connectors (J6001/J6002) on the CCD PCB and the connectors (J5002/J5003) on the reader controller PCB connected securely? NO: Connect the connectors securely. 2. CCD unit Try replacing the CCD unit. Is the problem corrected? YES: End. 3. Reader controller PCB, Main controller PCB Try replacing the reader controller PCB. Is the problem corrected? YES: End. NO: Check the wiring; if normal, replace the main controller PCB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie