Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Epson AcuLaser C4100 — Trang 2/4

Code: 103

Description: CTD sensor error
Remedy: 1 Initial setting Do the following checks show a problem? • Sensor Assy ADC installation Reinstall applicable parts. Go to step 2. 2 BTR Assy check 1. Replace the BTR Assy. (Refer to Ch4-4.2.12.2) 2. Turn On the power. Does an error occur even when a new BTR Assy is installed? Go to step 3. End of procedure 3 PHD Assy check 1. Replace the PHD Assy. 2. Turn On the power. Does an error occur even when a new PHD Assy is installed? Go to step 4. End of procedure 4 Harness Assy CTD continuity check 1. Remove the Sensor Assy ADC. (Refer to Ch4-4.2.9.2) 2. Disconnect the P/J1361 replay connector from the Harness Assy Front 1 and the Harness Assy CTD. 3. Check the continuity for the following lines. J136-1 <=> J1361-5 J136-2 <=> J1361-4 J136-3 <=> J1361-3 J136-4 <=> J1361-2 J136-5 <=> J1361-1 Is the continuity between J136 <=> J1361 normal? Go to step 5. Replace the Harness Assy CTD . 5 Harness Assy Front 1 continuity check 1. Remove the P/J13 connector from the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the continuity for the following lines. J13-12 <=> P1361-5 J13-13 <=> P1361-4 J13-14 <=> P1361-3 J13-15 <=> P1361-2 J13-16 <=> P1361-1 Is the continuity between J13 <=> P1361 normal? Go to step 6. Replace the Harness Assy Front 1 . 6 Replace the Sensor Assy ADC (Refer to Ch4-4.2.9.2) 1. Replace the Sensor Assy ADC. (Refer to Ch4-4.2.9.2) 2. Turn On the power. Does the error still occur? Go to step 7. End of procedure 7 5V DC power supply 1. Disconnect the P/J41 connector from the PWB Drive . 2. Measure the voltage between P41-24 <=> P41-21/22. Is there 5V DC between P41-24 <=> P41-21/22? Go to step 8. Go to step 10. 8 Harness Assy DRV 1 continuity 1. Disconnect the P/J11 connector from the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the continuity between J41-24 <=> J11-17. Is the continuity normal between J41-24 <=> J11-17 normal? Go to step 9. Replace the Harness Assy DRV 1 . 9 Sensor Assy ADC 1. Replace the Sensor Assy ADC. (Refer to Ch4-4.2.9.2) 2. Turn On the power. Does an error occur even when a new Sensor Assy ADC is installed? Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) End of procedure 10 PWB Drive continuity 1. Disconnect the P/J61 connector from the PWB Drive. 2. Measure the voltage between J61-8 <=> J61-7. Is there 5V DC between J61-8 <=> J61-7. Replace the PWB Drive. (Refer to Ch4-4.2.18.5) Go to step 11. 11 Harness Assy LVNC continuity 1. Disconnect the P/J165 connector from the LVPS . 2. Measure the voltage between P165-1 <=> P165-2. Is there 5V DC between P165-1 <=> P165-2. Replace the Harness Assy LVNC . Go to FIP-DC .

Code: 104

Description: Fan motor error
Remedy: 1 Initial setting Do the following checks show a problem? • Fan Fuser installation • Fan Rear installation Reinstall applicable parts. Go to step 2. 2 Fan Rear Fail signal Measure the following voltages at the PWB Drive connector. P/J42-29 <=> P/J42-14/15 Is there 3.3V DC between P/J42-29 <=> P/J42-14/15? Go to step 3. Go to step 5. 3 Power supply to Fan Rear Measure the voltage between connectors P/J166-1 <=> P/J166-3 of the LVPS . Is the voltage 15V DC or 24V DC between P/J166-1 <=> P/J166-3? Go to step 4. Replace the LVPS. (Refer to Ch4-4.2.18.3) 4 Fan Rear 1. Replace the Fan Rear. (Refer to Ch4-4.2.18.2) 2. Turn On the power. Does the problem still occur? Replace the PWBA MCU & HVPS. Problem solved. 5 Fan Fuser Fail signal Measure the following voltages at the PWB Drive connector. P/J42-27 <=> P/J42-14/15 Is there 3.3V DC between P/J42-27 <=> P/J42-14/15? Go to step 6. Replace the PWBA MCU & HVPS. 6 Power supply to Fan Fuser Measure the following voltages at the PWB Drive connector. P/J50-7 <=> P/J50-9 Is there 24V DC between P/J50-7 <=> P/J50-9? Go to step 7. Replace the PWB Drive. (Refer to Ch4-4.2.18.5) 7 Fan Fuser 1. Replace the Fan Fuser. (Refer to Ch4-4.2.4.3) 2. Turn On the power. Does the problem still occur? Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) Problem solved.

Code: 105

Description: Low density error
Remedy: 1 Initial setting Do the following checks show a problem? • BTR Assy installation • Sensor Assy ADC installation • PHD Assy installation • Remaining Toner Reinstall applicable parts. Go to step 2. 2 BTR Assy check 1. Replace the BTR Assy. (Refer to Ch4-4.2.12.2) 2. Turn On the power. Does an error occur even when a new BTR Assy is installed? Go to step 3. End of procedure 3 PHD Assy check 1. Replace the PHD Assy. 2. Turn On the power. Does an error occur even when a new PHD Assy is installed? Go to step 4. End of procedure 4 Harness Assy CTD connection check Check the P/J136 connector of the Harness Assy CTD and sensor Assy ADC . (Refer to Ch4-4.2.9.2) Is the Harness Assy CTD connected correctly to the Sensor Assy ADC? Go to step 5. Reinstall applicable parts. 5 Harness Assy CTD continuity check 1. Disconnect the P/J136 connector from the Sensor Assy ADC . 2. Disconnect the P/J1361 relay connector between the Harness Assy CTD and the Harness Assy Front 1 . 3. Check the continuity for the following lines. J136-1 <=> J1361-5 J136-2 <=> J1361-4 J136-3 <=> J1361-3 J136-4 <=> J1361-2 J136-5 <=> J1361-1 Is the continuity between J136 <=> J1361 normal? Go to step 6. Replace the Harness Assy CTD . 6 Harness Assy Front 1 continuity check 1. Disconnect the P/J13 connector from the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the continuity for the following lines. P1361-1 <=> J13-16 P1361-2 <=> J13-15 P1361-3 <=> J13-14 P1361-4 <=> J13-13 P1361-5 <=> J13-12 Is the continuity between P1361 <=> J13 normal? Go to step 7. Replace the Harness Assy Front 1 . 7 5V DC power supply 1. Disconnect the P/J41 connector from the PWB Drive . 2. Measure the voltage between P41-24 <=> P41-21/22. Is there 5V DC between P41-24 <=> P41-21/22? Go to step 8. Go to step 10. 8 Harness Assy DRV 1 continuity 1. Disconnect the P/J11 connector from the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the continuity between J41-24 <=> J11-17. Is the continuity normal between J41-24 <=> J11-17 normal? Go to step 9. Replace the Harness Assy DRV 1 . 9 Sensor Assy ADC 1. Replace the Sensor Assy ADC. (Refer to Ch4-4.2.9.2) 2. Turn On the power. Does an error occur even when a new Sensor Assy ADC is installed? Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) End of procedure 10 PWB Drive continuity 1. Disconnect the P/J61 connector from the PWB Drive. 2. Measure the voltage between J61-8 <=> J61-7. Is there 5V DC between J61-8 <=> J61-7. Replace the PWB Drive. (Refer to Ch4-4.2.18.5) Go to step 11. 11 Harness Assy LVNC continuity 1. Disconnect the P/J165 connector from the LVPS . 2. Measure the voltage between P165-1 <=> P165-2. Is there 5V DC between P165-1 <=> P165-2. Replace the Harness Assy LVNC . Go to FIP-DC .

Code: 106

Description: Firmware error
Remedy: 1 Does the error occur even when the power is turned Off and back On? Go to step 2. See if the problem recurs; if it does, go to step 2. 2 Harness Assy EEPROM connection check Check the connection of the P/J144 connector of the PWB EEPROM . Is P/J144 correctly connected? Go to step 3. Connect P/J144 correctly. 3 3.3V DC power supply to PWB EEPROM 1. Disconnect the P/J144 connector from the PWB EEPROM. 2. Measure the voltage between J144-2 <=> J144-1. Is there 3.3V DC between J144-2 <=> J144-1? Go to step 7. Go to step 4. 4 3.3V DC power supply to PWB Drive 1. Disconnect the P/J61 connector from the PWB Drive. 2. Measure the voltage between J61-6 <=> J61-5. Is there 3.3V DC between J61-6 <=> J61-5? Go to step 5. Go to FIP-DC . 5 Harness Assy EEPROM connection 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the connection of the P/J140 connector of the PWBA MCU & HVPS . Is P/J140 correctly connected? Go to step 6. Connect P/J140 correctly. 6 Harness Assy EEPROM continuity 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Disconnect the P/J140 connector from the PWBA MCU & HVPS . 3. Check the continuity for the following lines. J140-9 <=> J144-2 J140-10 <=> J144-1 Is there continuity in all lines between J140 <=> J144? Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) Replace the Harness Assy EEPROM . 7 PWB EE8 Harness Assy EEPROM connection 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Check the connection of the P/J140 connector of the PWBA MCU & HVPS . Is P/J140 correctly connected? Go to step 9. Connect P/J140 correctly. 9 Harness Assy EEPROM continuity 1. Remove the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) 2. Disconnect the P/J140 connector from the PWBA MCU & HVPS . 3. Check the continuity for the following lines. J140-7 <=> J144-4 J140-8 <=> J144-3 Is there continuity in all lines between J140 <=> J144? Go to step 10. Replace the Harness Assy EEPROM . 10 PWBA MCU & HVPS 1. Replace the PWBA MCU & HVPS with a new part. (Refer to Ch4-4.2.18.1) 2. Turn On the power. Does the problem still occur? Go to FIP-Noise . Problem solved.PROM 1. Replace the PWB EEPROM. (Refer to Ch4-4.2.15.8) 2. Turn On the power. Does the error code still appear? Go to step 8. Problem solved.

Code: 107

Description: Environment sensor error
Remedy: 1 Initial setting Do the following checks show a problem? • Sensor Hum Temp installation Reinstall applicable parts. Go to step 2. 2 Connector connections 1. Remove the Housing Assy Elec. (Refer to Ch4-4.2.13.1) 2. Check the connection of the P/J24 connector of the PWBA MCU & HVPS . 3. Remove the Cover Side L. (Refer to Ch4-4.2.4.14) 4. Check the connection of the P/J2361 relay connector between the Harness Assy TMPB and the Harness Assy TMPA . 5. Check the connection P/J231 connector of the Sensor Assy ADC . Are the connectors connected correctly? Go to step 3. Reconnect the connector or replace the parts. 3 Sensor Hum Temp signal check Measure the voltage at the P/J2361 relay connector between the Harness Assy TMPB and the Harness Assy TMPA . P/J2361-1 <=> P/J2361-2 (3V DC or 0.1V DC or less) P/J2361-3 <=> P/J2361-2 (2.5V DC or more) Are the voltages between P/J2361 <=> P/J2361 within the ranges? Go to step 5. Go to step 4. 4 Sensor Hum Temp signal check 1. Remove the Sensor Hum Temp. (Refer to Ch4-4.2.7.5) 2. Connect the P/J231 connector of the Sensor Hum Temp. 3. Measure the voltages between the following terminals. P/J231-4 <=> P/J231-3 (3V DC or 0.1V DC or less) P/J231-2 <=> P/J231-3 (2.5V DC or more) Are the voltages between P/J231 <=> P/J231 within the ranges? Replace the Harness Assy TMPA . Go to step 5. 5 Power supply to Sensor Hum Temp Measure the vo6 Harness Assy TMPA , Harness Assy TMPB continuity Check the continuity for the following lines. J24-1 <=> P2361-4/J2361-1 <=> J231-4 J24-2 <=> P2361-3/J2361-2 <=> J231-3 J24-3 <=> P2361-2/J2361-3 <=> J231-2 J24-4 <=> P2361-1/J2361-4 <=> J231-1 Is there continuity in all lines? Go to step 7. Replace the harness with no continuity. 7 PWBA MCU & HVPS continuity 1. Disconnect the P/J11 and P/J24 connector from the PWBA MCU & HVPS. (Refer to Ch4- 4.2.18.1) 2. Check the continuity between P11-17 <=> P24-4. Is the continuity normal between P11-17 <=> P24-4 normal? Replace the PWBA MCU & HVPS. (Refer to Ch4-4.2.18.1) Go to step 8. 8 Harness Assy DRV 1 continuity 1. Disconnect the P/J41 connector from the PWB Drive . 2. Measure the voltage between connectors P41-24 <=> P42-14/15 of the PWB Drive. Is there 5V DC between P41-24 <=> P42-14/15. Replace the Harness Assy DRV 1 . Go to step 9. 9 PWB Drive continuity 1. Disconnect the P/J61 connector from the PWB Drive. 2. Measure the voltage between J61-8 <=> J61-7. Is there 5V DC between J61-8 <=> J61-7. Replace the PWB Drive. (Refer to Ch4-4.2.18.5) Go to step 10. 10 Harness Assy LVNC continuity 1. Disconnect the P/J165 connector from the LVPS . 2. Measure the voltage between P165-1 <=> P165-2. Is there 5V DC between P165-1 <=> P165-2. Replace the Harness Assy LVNC . Go to FIP-DC .ltage between P231-1 <=> P231-3. Is there +5V DC between P/J231-1 <=> P/J231-3? Replace the Sensor Hum Temp. (Refer to Ch4-4.2.7.5) Go to step 6.

Code: 1100, 1101

Description: 1100 ROM checksum error (bit 0 ~ 15) (Font) 1101 ROM checksum error (bit 16 ~31) (Font)
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Replace the CODE ROM-DIMM (C309PROG): • Replace the mounted CODE ROM-DIMM. Does the problem still occur? Replace the CONTROLLER PWB. Problem solved.

Code: 1120 ... 1123

Description: 1120 ROM checksum error (bit 0 ~ 7) (Program) 1121 ROM checksum error (bit 8 ~ 15) (Program) 1122 ROM checksum error (bit 16 ~ 23) (Program) 1123 ROM checksum error (bit 24 ~ 31) (Program)
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Replace the CODE ROM-DIMM (C309PROG): • Replace the mounted CODE ROM-DIMM. Does the problem still occur? Replace the CONTROLLER PWB. Problem solved.

Code: 1180, 1185

Description: 1185 Unsupported ROM module 1200 EEPROM write error
Remedy: 1 Initial setting: • Remove all the optional units and modules related to the electrical system and bring the printer back to the standard status. • Check if all connectors are properly connected to the CONTROLLER PWB. Replace or reinstall the relevant part. Go to step 2. 2 Checking the DIMM: • Insert the DIMM in the socket until it is locked securely. NOTE: Since the DIMM has the right direction and location for insertion, be sure to insert it in the correct direction and location. • Check if the DIMM is available for this printer, AcuLaser C4000. In cases other than above, replace the CONTROLLER PWB. Replace or reinstall the relevant part. Problem solved.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie