• Code: 00010008
• Description: Servo interrupt watchdog time-out error
  The printer causes this error and stops operation if it detects a watchdog time-out on the DC motor drive circuit (CPU or ASIC) while the CR or PF Motor is driving.
• Causes:
• Remedy: CPU or ASIC failure can be considered as the cause of the error, replace the Main Board Assy. Replace the BOARD ASSY., MAIN .

• Code: 00010009
• Description: System interrupt watchdog time-out error
  The printer causes this error and stops operation if it detects an out-of-control state or cache failure in the CPU or ASIC while the BOARD ASSY.,MAIN is processing a print data.
• Causes:
• Remedy: CPU or ASIC failure can be considered as the cause of the error, replace the Main Board Assy. Replace the BOARD ASSY., MAIN .

• Code: 0001000A
• Description: Carriage home position detection error
  The printer causes this error and stops operation if it cannot detect the Carriage home position or cannot detect it within a fixed time period during the power-on initialization operation or while performing home position detecting operation during printing.
• Causes:
• Remedy: 1. Clean dirt or foreign materials on the CR HP Sensor and check if it is damaged. 2. Replace the CR HP Sensor . 3. Replace the BOARD ASSY., MAIN .

• Code: 0001000C
• Description: PG home position detection error
  The printer causes this error and stops operation if it cannot detect the PG home position during the power-on initialization operation or while performing platen gap changing operation after paper is set.
• Causes: • The PG HP Sensor connector is disconnected. • The Pump Motor connector is disconnected. • The Pump Motor harness is broken. • PG HP Sensor failure • Pump Motor failure • The PG drive gears are damaged. • The fuse for the motor driver is blown. (on the Main Board)
• Remedy: 1. Reconnect the PG HP Sensor connector or the Pump Motor connector securely. 2. Replace the PG HP Sensor . 3. Replace the PUMP CAP ASSY. .

• Code: 00010014
• Description: Failure of pressurizing
  The printer causes this error and stops operation if it detects an abnormal condition of the Pressure Sensor (air leak from the pressurizing mechanism) during the power-on initialization operation or while performing ink supply operation.
• Causes: • Pressure Motor failure • The connector of the Pressure Motor, Regulator Solenoid or Pressure Sensor is disconnected. • The harness of the Pressure Motor, Regulator Solenoid or Pressure Sensor is broken. • Regulator Solenoid failure (does not become ON) • Pressure Sensor failure • The Pressure Tube is disconnected. • The fuse for the Solenoid or the motor driver is blown. (on the Main Board)
• Remedy: 1. Reconnect the connectors of the Pressure Motor, Regulator Solenoid or Pressure Sensor securely. 2. Connect the Pressure Tube. 3. Replace the PUMP ASSY., SUPPLY . 4. Replace the BOARD ASSY., MAIN .

• Code: 0001001B
• Description: Head driver (TG) temperature error
  The printer causes this error and stops operation if it detects an abnormal internal temperature of the printhead by the thermistor in the head while performing printing operation without firing ink from the nozzles.
• Causes: • The printhead internal temperature rises because of a printing operation without firing ink. • A breakdown of the printhead • Poor contact, short or disconnection of the tape electric wires • Main Board failure. (A/D of the CPU is damaged)
• Remedy: 1. Check if the printer can recover from the error by turning it OFF and back ON. 2. Replace the PRINT HEAD . 3. Replace the BOARD ASSY., MAIN .

• Code: 0001001D
• Description: CR servo parameter error
  The printer causes this error and stops operation when it detects that a voltage beyond the prescribed range is output to the CR Motor.
• Causes:
• Remedy: 1. Clean dirt or paper dust on the Timing Fence and check if it is damaged. 2. Execute the CR Timing Belt Tension Adjustment . 3. Replace the CR Encoder Sensor . 4. Replace the CR MOTOR ASSY. . 5. Replace the BOARD ASSY., MAIN .

• Code: 0001001E
• Description: PF servo parameter error
  The printer causes this error and stops operation when it detects that a voltage beyond the prescribed range is output to the PF Motor.
• Causes:
• Remedy: 1. Clean dirt or paper dust on the Loop Scale and check if it is damaged. 2. Execute the PF Timing Belt Tension Adjustment . 3. Replace the PF Encoder Sensor . 4. Replace the PF MOTOR ASSY. . 5. Replace the BOARD ASSY., MAIN .