Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP Color LaserJet 2500 — Trang 2/3

Code: 09

Image:
Description: General Attention with Ability to Continue error
The Attention light, Ready light, and Go light are blinking.
Remedy: 1 Press (GO) to try to continue printing. 2 If the error persists, switch printer drivers and try again to print.

Code: 10

Image:
Description: 68.x Permanent Storage error
The Attention light is blinking. The nonvolatile memory (NVRAM) is temporarily full.
Remedy: 1 Press (GO) to clear the message. Check the printer settings. 2 Remove the Jetdirect card, if it is installed (HP color LaserJet 2500 series printers only), and then perform a cold reset. 3 Perform a NVRAM init.

Code: 11

Image:
Description: Accessory error secondary messages
8x.yyyy EIO error The Attention light is blinking. A problem exists with the print server card. CAUTION: You must turn off the printer before inserting or removing the print server card to avoid damaging the print server card.
Remedy: 1 Remove the print server card and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported print server card. See chapter 7 for ordering information. 3 To continue printing, remove the print server card from the EIO port and connect a parallel or USB cable. You must change the port or reinstall the software. 4 If the print server card still is not working, replace the print server.

Code: 12

Image:
Description: Accessory error secondary messages
53.x1.zz Printer (DIMM Slot 1) error The Go light is on. A problem exists with the DIMM in DIMM slot 1.
CAUTION: You must turn off the printer before inserting or removing DIMMs to avoid damaging them.
Remedy: 1 Remove the DIMM and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported DIMM. See chapter 7 for ordering information. 3 Move the DIMM to a different DIMM slot. If the DIMM works in a different slot, then DIMM slot 1 is malfunctioning. NOTE: Many of the first printers of this model were shipped with an 8 MB flash DIMM in DIMM slot 1. If the printer has an 8 MB flash DIMM in DIMM slot 1, then replace the DIMM. The 8 MB flash DIMM will not work in any DIMM slot other than DIMM slot 1. 4 To continue printing, remove the DIMM from DIMM slot 1.

Code: 13

Image:
Description: Accessory error secondary messages
53.x2.zz Printer (DIMM Slot 2) error
The Ready light is on. A problem exists with the DIMM in DIMM slot 2.
CAUTION: You must turn off the printer before inserting or removing DIMMs to avoid damaging them.
Remedy: 1 Remove the DIMM and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported DIMM. See chapter 7 for ordering information. 3 Move the DIMM to a different DIMM slot. If the DIMM works in a different slot, then DIMM slot 2 is malfunctioning. 4 To continue printing, remove the DIMM from DIMM slot 2.

Code: 14

Image:
Description: Accessory error secondary messages
53.x3.zz Printer (DIMM Slot 3) error
The Attention light is on. A problem exists with the DIMM in DIMM slot 3.
CAUTION: You must turn off the printer before inserting or removing DIMMs to avoid damaging them.
Remedy: 1 Remove the DIMM and reinstall it to make sure that it is correctly installed. 2 Make sure that you are using a supported DIMM. See chapter 7 for ordering information. 3 Move the DIMM to a different DIMM slot. If the DIMM works in a different slot, then DIMM slot 3 is malfunctioning. 4 To continue printing, remove the DIMM from DIMM slot 3.

Code: 15

Image:
Description: Service error secondary messages
51.x Bad beam detect error
The Attention, Ready, and Go lights remain on.
Remedy: 1 Press (GO). The page that contains the error will automatically be reprinted. 2 Turn the printer off and then back on. 3 Replace the laser/scanner.

Code: 16

Image:
Description: Service error secondary messages
52.x Scanner error
The Ready light is on.
Remedy: 1 Press (GO). The page that contains the error will automatically be reprinted. 2 Turn the printer off and then back on. 3 Turn the printer off, and then reseat the laser/scanner cable. 4 Replace the laser/scanner.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie