Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP DesignJet Z3100 — Trang 7/8

Code: 78.1:YZ

Description: Media settings area missing in media settings file.
Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version. • Update the OMES of the paper type that is failing.

Code: 78:08

Description: The job received can not be printed without borders on this paper.
Remedy: • Use a paper that supports borderless printing. • This system error code does NOT require service help. It should be resolved by the customer.

Code: 79.1:YZ

Description: Recoverable firmware error that does not stop the printing process.
Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.

Code: 79:YZ

Description: Generic Firmware error.
Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.

Code: 81:YZ

Description: Problem with paper advance. This source of error could come from an error in any of the following systems: paper motor, disk encoder, cables or main electronics.
Remedy: Initial checks: This error can occur because the printer has been dropped during transportation, causing structural damage. Before continuing with the 81:YZ troubleshooting, first look for structural damage. To identify the structural damage, look for the following three things: • Consistent 81:YZ error codes. • Platen fingers rubbing on the roller surface, leaving black marks on the roller. • A gap on the platen beam. If there’s any gap in Z (vertical direction) between the plastic feature of the platen and the metal side plate, then the chassis is damaged and the unit cannot be repaired.
Corrective Action: • Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Perform the Media Drive diagnostic test to troubleshoot the problem further. • Check the connections on the Main PCA; the Media Advance Drive is connected to the connector labeled Paper Motor. • Adjust the encoder disc and motor mount configuration . See the installation instructions on. • If the System Error continues, replace the Media Advance Transmission.

Code: 85:YZ

Description: Problem finding the Drive Roller zero.
Remedy: • Check that the Media Advance Drive is connected properly to the Main PCA and is not damaged. The cable is labeled “Paper Motor.” • Perform the Media Drive diagnostic test to troubleshoot the problem further. • If the System Error continues, replace the Encoder Disk and Encoder Sensor. • If the System Error continues, replace the Main PCA.

Code: 86:01

Description: Problem moving the carriage, most likely due to a paper jam.
Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Open the Window and check for any visible obstacles restricting the movement of the carriage. If there is a wrinkled mass of media inside the paper path, lift the Pinch wheels (using the Media Lever) and clear the obstruction. • If there is no paper jam or obstacle blocking the carriage movement perform the following: – Clean the encoder strip. – Check the belt assembly. – All cables and connections between the Carriag PCA, Scan Axis Motor, and Main PCA. – Oil the carriage rails. • Perform the Scan Axis Diagnostic Test . Page 3-6. • If the diagnostic test does not find any specific error, replace the Carriage Assembly. • Replace the Belt Assembly. • Replace the Scan Axis Motor. • Replace the Main PCA.

Code: 87:YZ

Description: Problem finding the Scan-axis encoder reading.
Remedy: • Upgrade the firmware. • Clean the Encoder Strip. • Replace the Encoder Strip. • Replace the Carriage PCA. • Replace the Trailing Cables.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie