Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub 195

Code: C0211

Description: Bypass tray up/down failure
- While the bypass lift sensor (PS2) is in the OFF state after the power is turned ON, output is finished, or a paper jam is cleared, PS2 is not turned ON within the given time after the bypass pick-up solenoid (SD1) has been turned ON. Then SD1 is turned ON again, but PS2 cannot be turned ON within the given time.
- When the bypass lift sensor (PS2) is in the ON state, PS2 is not turned OFF within the given time after the bypass pick-up solenoid (SD1) has been turned ON.
Remedy: 1 Check the connector between M1-MFPB P006 for proper connection and correct as necessary. 2 Check M1 for correct drive coupling and correct as necessary. 3 Check the connector between CL1-relay CN3-relay CN6- MFPB P008 for proper connection and correct as necessary. 4 CL1 operation check. 5 Check the connector between SD1-relay CN4-relay CN6- MFPB P008 for proper connection and correct as necessary. 6 M1 operation check. 7 SD1 operation check. 8 Change MFPB.

Code: C03FF

Description: Faulty model setting
- “Model Setting” of “Adjust” available from the Service mode is incorrectly set.
Remedy:

Code: C2351

Description: Cooling fan motor malfunction
- The fan lock signal remains HIGH for a predetermined continuous period of time while the cooling fan motor (FM2) is turning.
Remedy: 1 Check the connector between FM2-relay CN27-MFPB P013 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM2 operation check. 4 Change MFPB.

Code: C2557

Description: Abnormally low toner density detected TCR sensor board
- The T/C ratios detected by the TCR sensor board (TCRSB) are below the threshold for the detection of abnormally low T/C ratio for three successive times. However, if a toner empty condition is detected, this abnormality is not detected.
Remedy: 1 Check to see if developer is available. 2 Check the connector between TCRSB-relay CN14-MFPB P010 for proper connection and correct as necessary. 3 Change TCRSB. 4 Change MFPB.

Code: C2558

Description: Abnormally high toner density detected TCR sensor board
- The T/C ratios detected by the TCR sensor board (TCRSB) are above the threshold for the detection of abnormally high T/C ratio for three successive times.
- The connector between MFPB to TCRSB is disconnected.
Remedy: 1 Check to see if developer is available. 2 Check the connector between TCRSB-relay CN14-MFPB P010 for proper connection and correct as necessary. 3 Change TCRSB. 4 Change MFPB.

Code: C255C

Description: TCR sensor board adjustment failure
- When TCR AUTO ADJUST is performed, the difference between the TCR sensor output voltage determined by TCR AUTO ADJUST and the standard voltage is greater than the threshold value.
Remedy: 1 Check to see if developer is available. 2 Check the connector between TCRSB-relay CN14-MFPB P010 for proper connection and correct as necessary. 3 Change TCRSB. 4 Change MFPB.

Code: C2702

Description: Abnormal image transfer voltage (HV)
- The image transfer voltage remains more than 100 V continuously for a given period of time while the drum remains stationary.
Remedy: 1 Check the transfer roller unit for installation. 2 Change HV1. 3 Change MFPB.

Code: C3451

Description: Warming-up failure
- The thermistor/1 (TH1) detected that the temperature of the surface of the fusing roller did not reach the specified level even after the lapse of given period of time has passed during warm-up.
Remedy: 1 Check the fusing unit for correct installation. 2 Check the open/close operation of the right door. 3 Check the fusing unit, DCPU and MFPB for proper connection and correct or change as necessary. 4 Change fusing unit. 5 Change MFPB. 6 Change DCPU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie