• Code: C9402
• Description: Exposure turning on the lamp abnormally detection
  • The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or more at the end of a scan job
• Remedy: 1 Check the connection between the lamp harness and the inverter board, and correct if necessary. 2 Check the connector between INVB CN1- REYB/SCAN PJ7 for proper connection and correct as necessary. 3 Check the connector between REYB/ SCAN PJ2-MFPB PJ14 for proper connection and correct as necessary. 4 Check the connector between CCDB PJ2- MFPB PJ01 for proper connection and correct as necessary. 5 Change INVB. 6 Change exposure unit. 7 Change CCDB. 8 Change REYB/SCAN.

• Code: CA051
• Description: Standard controller configuration failure
  • The controller of the MFP board (MFPB) is faulty.
• Remedy: 1 Check to see if the following setting has been correctly made: [Service Mode] - [System 2] - [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB.

• Code: CA052
• Description: Controller hardware error
  • A controller hardware error is detected in the network I/F.
• Remedy: 1 Check to see if the following setting has been correctly made: [Service Mode] - [System 2] - [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB.

• Code: CA053
• Description: Controller start failure
  • A controller start failure is detected in the controller interface.
• Remedy: 1 Check to see if the following setting has been correctly made: [Service Mode] - [System 2] - [Image Controller Setting]. If changing the setting, turn OFF the main power switch and turn it ON again after 10 seconds or more. 2 Check the connectors of the MFP board (MFPB) for proper connection and correct as necessary. 3 Change MFPB.

• Code: CC001
• Description: Vendor connection failure
  • It is detected that communications with the vendor are interrupted for a given period of time or more with “Installed” selected for the setting of vendor installation
• Remedy: 1 Check the connector between vendor- PRCB CN17 for proper connection and correct as necessary. 2 Change PRCB. 3 Change vendor.

• Code: CC151
• Description: ROM contents error upon startup (MSC)
  • A fault is detected in a sequence of ROM contents check of the MFPB during starting
• Remedy: 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. MSC: MFP board (MFPB) IR: MFP board (MFPB) PRT: Printer control board (PRCB)

• Code: CC152
• Description: ROM contents error upon startup (scanner)
  • A fault is detected in a sequence of ROM contents check of the MFPB during starting.
• Remedy: 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. MSC: MFP board (MFPB) IR: MFP board (MFPB) PRT: Printer control board (PRCB)

• Code: CC153
• Description: ROM contents error upon startup (PRT)
  • A fault is detected in a sequence of ROM contents check of the PRCB during starting.
• Remedy: 1 Check the ROM version. 2 Rewrite the firmware. 3 Replace the appropriate board. MSC: MFP board (MFPB) IR: MFP board (MFPB) PRT: Printer control board (PRCB)